Vs +1 + R www VR IR + VL LV. + C I. IL Consider the RLC circuit shown. The sinusoidal voltage source has a magnitude of V. Answer IV the following questions, showing your solutions where applicable. a. Find an expression for the complex gain, IA | b. Derive an expression for the cutoff frequency/ies of the circuit. (Hint: The cutoff frequency, w, is the frequency at which the output voltage is of the input voltage.) √2 c. What is the expected behavior of the output as the frequency approaches ∞? When the frequency approaches 0? d. At what frequency will the voltage gain be at a maximum?

Vs +1 + R www VR IR + VL LV. + C I. IL Consider the RLC circuit shown. The sinusoidal voltage source has a magnitude of V. Answer IV the following questions, showing your solutions where applicable. a. Find an expression for the complex gain, IA | b. Derive an expression for the cutoff frequency/ies of the circuit. (Hint: The cutoff frequency, w, is the frequency at which the output voltage is of the input voltage.) √2 c. What is the expected behavior of the output as the frequency approaches ∞? When the frequency approaches 0? d. At what frequency will the voltage gain be at a maximum?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the system defined by the first-order differential equation: Draw the log magnitude (dB)-log frequency graph of H(jw). (The phase graph is not required. The frequency axis is expected to be logarithmic when drawing the log magnitude graph.) The input is assumed to be suppressed when the magnitude of H(jw) is -40dB. It is given that the x(t)=coswat signal is suppressed by this system. What is the smallest value of wa in this case?
A second order system with a natural frequency (wn) of 6 rad/sec and damping ratio of x = 0.5, the value of maximum overshoot is equal to?
A circuit consists of a resistor (resistance R), inductor (inductance L), and capacitor (capacitance C) connected in series with an AC source supplying sinusoidal voltage V0cos(omegat). Assume that all circuit elements are ideal, so that the only resistance in the circuit is due to the resistor. Also assume that omega is the resonant frequency of the circuit. What is the average Pavg supplied by the voltage source?
Given the RLC circuit below and given that the sinusoidal voltage source has a magnitude of |Vs|, do the following: Find an expression for the complex gain (|Aω| = Vo / Vs) Derive an expression for the cutoff frequencies of the circuit (Note: The cutoff frequency is the frequency at which the output voltage is roughly 1/√2 of the input voltage) What is the expected behavior of the circuit as the frequency approaches infinity? What about when the frequency is 0? Finally, what is the frequency in which the voltage gain will be at maximum? Explain why.
A second order system with a natural frequency (wn) of 6 rad/sec and damping ratio of 0.5, the value of rise time?
2. Prove that , for a radio receiverOutput SNR in dB = Input SNR (dB) - Noise Figure(NF)[You can start the derivation from the relation connecting Noise Figure (NF)and Noise Ratio(F) ] note: the answe will be by hand written.
In the circuit in the figure, Vcc= 18 V, Rs1 = 0.9 k2, Rs2 = 0.5 kQ, R1 = 75 kQ, R2 = 15 kQ, RC = 2.2 kQ, RE = 1 k and B = 120. It is also known that Cwi = 6 pF, Cwo = 10 pF, Cbc = Cu = 7 pF, Cbe = C = 44 pF and Cce = 11 PF. Accordingly, considering the frequency response of the circuit, what would the high cutoff frequency (fH) be? NOTE-1: The output impedance of the transistor is ro = 20 k and will be taken into account in the calculations. NOTE-2: high frequency dependence of hfe, B. will be taken into account.
a modulating signal given by v(t)=20v; between -2 and 2s and v(t)=0 for another value multiplies the signal cos 400000pi t, Determine the expression in time and frequency of the DBL-PS signal for a power of 6500W
Electronic Since k = 0.35x10^3, VGSQ = 6.2 V, VGS(Th) = 2.4 V, RF = 100 MΩ, RG = 10 MΩ, RD = 7.6 kΩ, RS = 2.2 kΩ and RL = 21 kΩ in the circuit in the figure, the output voltage In which option is the amplitude value (Vout) given correctly? NOTE-1: E-MOSFET output impedance is rd = 70 kΩ and should be taken into account in calculations. NOTE-2: Capacitors are of negligible size at mid-band frequency. NOTE-3: It is within the 5 kHz mid-band frequency.
Since k = 0.35x10-3, VGSQ = 6.2 V, VGS(Th) = 2.4 V, RF = 100 MΩ, RG = 10 MΩ, RD = 7.6 kΩ, RS = 2.2 kΩ and RL = 8.7 kΩ in the circuit in the figure In which option is the amplitude value (Vout) of the output voltage given correctly? NOTE-1: E-MOSFET output impedance is rd = 70 kΩ and should be taken into account in calculations. NOTE-2: Capacitors are of negligible size at mid-band frequency. NOTE-3: It is within the 5 kHz mid-band frequency. Since k = 0.35x10-3, VGSQ = 6.2 V, VGS(Th) = 2.4 V, RF = 100 MΩ, RG = 10 MΩ, RD = 7.6 kΩ, RS = 2.2 kΩ and RL = 8.7 kΩ in the circuit in the figure In which option is the amplitude value (Vout) of the output voltage given correctly? NOTE-1: E-MOSFET output impedance is rd = 70 kΩ and should be taken into account in calculations. NOTE-2: Capacitors are of negligible size at mid-band frequency. NOTE-3: It is within the 5 kHz mid-band frequency.
In the circuit in the figure, Vcc= 18 V, Rs1 = 0.9 kohm, Rohm = 0.5 kQ, R1 = 75 kohm, R2 = 15 kohm, RC = 2.2 kohm, RE = 1 kohm and B = 120. It is also known that Cwi = 6 pF, Cwo = 10 pF, Cbc = Cu = 7 pF, Cbe = C = 44 pF and Cce = 11 PF. Accordingly, considering the frequency response of the circuit, what would the high cutoff frequency (fH) be? NOTE-1: The output impedance of the transistor is ro = 20 k and will be taken into account in the calculations. NOTE-2: high frequency dependence of hfe, B. will be taken into account.
What is the frequency response? What is the expression for the magnitude of the frequency response, could you also sketch it? ..