Water at 20°C flows from Tank 1 to Tank 2 through a 2-inch, Schedule 40 pipe as shown in the figure below. The length of the pipe is 100 m and in the pipeline, there are two 90° standard elbows and a gate valve. If both tanks are located at the same datum level, determine the water level in the larger tank if the water level in the smaller one is 4 m from the datum level and the flow rate of water is 1O L/s. [49.66 m] 4m Tank 1 Tank 2 I

Water at 20°C flows from Tank 1 to Tank 2 through a 2-inch, Schedule 40 pipe as shown in the figure below. The length of the pipe is 100 m and in the pipeline, there are two 90° standard elbows and a gate valve. If both tanks are located at the same datum level, determine the water level in the larger tank if the water level in the smaller one is 4 m from the datum level and the flow rate of water is 1O L/s. [49.66 m] 4m Tank 1 Tank 2 I

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 6 in. pipe, as shown in the figure, takes water from a reservoir and terminates in a nozzle having a jet diameter of 2 in. Assuming a nozzle loss of 8 percent of the velocity head in the jet, compute the discharge (in S.I. units). Also, make a table showing the elevation head, velocity head, pressure head, and total head at each of the six stations. Lastly, draw the hydraulic gradient line (H.G.L.) & the energy gradient line (E.G.L.).
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a pressure of 150 kPa. The throat diameter of the me- ter is 100 mm and the pressure at the throat is 400 mm of mercury below atmosphere. If 3% of the differential pressure is lost between inlet and the throat, determine the flow rate of the pipeline. PLEASE USE BERNOULLI'S ENERGY EQUATION. INCLUDE COMPLETE SOLUTION
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450 mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively. If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
Topics: Fundamental of fluid flow Water flows upwards in a vertical pipeline of gradually varyingsection from point 1 to point 2, which is 1.5m above point 1, at the rate of0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. Ifpressure at section 2 is 600 kPa, determine the pipe diameter at that location.Neglect losses.
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
A pipe reduces it size from 300mm diameter at point 1, to 100mm diameter at point 2. The pressure at point 1 is 200KPa, and point 2 is 7m higher in elevation than point 1. The discharge on the pipe is 30 L/s and the head loss from point 1 to 2 is 10% of the pressure head at point 1. Determine the pressure at point 2 if a) the liquid is water, b) if the liquid is oil (SG = 0.8) and c) if the liquid is glycerin (SG = 1.3)
reservoir with water pressurized pipe diameter is 5 cm. The head loss in the system as given by hL= 5V^ 2/ 2g. The height between the water surface and the pipe outlet is 400 m. A discharge of 0.11 m3 /s is needed. What must the pressure in the tank be achieve such a flow rate? Assume a turbulent flow.
Problem 5: A fluid flows by gravity down an 8-cm galvanized ironpipe. The pressures at the higher and lower locations are 120 kPaand 140 kPa, respectively. The horizontal distance between thetwo locations is 30 m, and the pipe has a slope of 1-m rise per10 m of run (horizontal distance). For a fluid with a kinematicviscosity of 10-6 m2/s and a density of 900 kg/m3, determinethe flow rate (in m3/s).
HW Question : The tank-pipe system is to deliver at least 12.5 m3/h of water at 20°C to the reservoir. What is the maximum roughness height ε allowable for the pipe? Neglect minor losses.
This is a fluid machine question. Water reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 98.08 kPa is maintained in the summit water discharge is 30 m above the reservoir. The quantity pumped is 0.50 m3/s. rrictional losses in the discharge and suction pipe of the pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm, what amount of energy must be furnished by the pump in kW?
A vertical pipe in the form of a cone has a diameter of 45 cm at the top and 92 cm at the bottom and is 18.3 m long. The head loss is 3 m in either direction when the velocity at the top is 9.15 m/s and the pressure head there is 1.98 m of water. Find the pressure head at the bottom when the flow is (a) downward (b) upward. Draw the diagram.