water at 25 °C from a tank and takes it to point B at a rate of 0.095 m3/s. a) Calculate the height "h" that is required for the water level in the tank in order to maintain a pressure of 100 KPa. at point A. b) If we assume that the pressure in the point A is equal to 75 KPa, calculate the power transmitted by the pump to the water in order to maintain a pressure of 275 KPa at point B. Include the energy losses due to friction, but ignore the others. в Flujo Flujo 8 m Tuberia de PVC de 800 m de largo y de un diametro de 8 pulg A Tuberia de PVC de 15 m de largo y de un diametro de 10 pulg.

water at 25 °C from a tank and takes it to point B at a rate of 0.095 m3/s. a) Calculate the height "h" that is required for the water level in the tank in order to maintain a pressure of 100 KPa. at point A. b) If we assume that the pressure in the point A is equal to 75 KPa, calculate the power transmitted by the pump to the water in order to maintain a pressure of 275 KPa at point B. Include the energy losses due to friction, but ignore the others. в Flujo Flujo 8 m Tuberia de PVC de 800 m de largo y de un diametro de 8 pulg A Tuberia de PVC de 15 m de largo y de un diametro de 10 pulg.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.113P: Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels...

See similar textbooks

Similar questions

PUMP DISCHARGES 150 LITERS PER SECOND OF WATER TO A HEIGHTOF 80 METERS. IF THE EFFICIENCY IS 80% AND THE SPEED OF THE PUMP IS 1800 RPM, WHAT IS THE TORQUE IN N-M TO WHICH THE DRIVE SHAFT IS SUBJECTED?
A stream of water, 3” in diameter, discharges into the atmosphere at a velocity 80.0 ft/sec. Find the horsepower in the jet using the datum plane through the center of the jet. Draw the figure.
a pump is delivering 160 liters per sec of water using an impeller diameter of 240 mm and operating at a speed of 1800 rpm. if the speed held constant and the impeller diameter is change to 203.2 mm, what is the new dischange og the pump in liters per second
A horizontal water pipe is reduced in size from 18 inches in diameter from point A to 6 inches in diameter to point B. The flow in the pipe is 10 cubic feet per second, and the pressure in A is 20 psi (gage). If it is assumed that there is no less energy due to friction, what is the pressure at B?
An open vessel of water accelerates up to a 30ᵒ plane at 2 m/s². a). What is the angle the water surface makes with the horizontal? B). If the angle mage by the water surface to the horizontal is increased to 25.21ᵒ, what will be the depth of water at the rear side of the vessel, if the initial depth of water at the rear side is 4m and the front is 2m before accelerating? The vessel has a length of 4m and 2m width. C). If the vessel’s depth at the rear side is 5m, what will be the volume spilled if the acceleration is increased to 15m/s²?
Find the acceleration of an open cylinder with 5 m diameter and holding - 6 m of water if the force acting on the sides is 90 kN.
Solve this now in 30 min plz
A jet of water impinges on a single smooth flat vane at its centre. The velocity of the jet is 70 m/s and the diameter 120 mm.Calculate the force on the vane, if it is moving with a velocity of 30 m/s in the direction of jet. Determine the power and efficiency. Also, find the speed of plate at which maximum efficiency may occur.
Two geometrically similar pumps are running at the same speed of 1000 rpms One pump has impoller diameter of 300 mm and lift water at the rate of 0.02 m3 against a head of 15 m Determine the head and impeller diameter of the other pump to deliver half the discharge.
The water in figure 6 flows steadily at 20°C through the box shown, entering through section (1) at 2 m / s. Find (a) the horizontal and (b) vertical forces required to hold the box still.
A jet of water strikes a stationary curved plate at one end at an angle of 30°. The jet of 75 mm diameter has a velocity of 30 m/s. The jet is deflected at an angle of 160° with respect to the horizontal. Determine the magnitude and direction of the force exerted by the water on the plate. Assume an ideal fluid. (Express Area in m2; Velocity in m/s; Discharge in m3/s and Force in N) The volumetric flow rate is:
A gate rotates at point A and releases water when the water's depth, d, exceeds a certain value. The gate's width (perpendicular to the image) is b = 2.95 ft, the water's depth is d = 4.82 ft, and point A is located at h = 2.41 ft. a) What is F, the magnitude of the horizontal force exerted on the gate by the water? The water's specific weight is γw=62.4lb/ft3. b) What are Ax and Bx, the horizontal reaction forces at points A and B that act on the gate from Part A. c) What is dmax, the water's maximum depth before the pressure causes the gate from part A to open?