Water flow from a large tank (T1) through a pipe Pipe X which splits into two smaller pipes, which discharges and flow out freely on Pipe Y and Pipe Z on as shown on the figure below. • Diameter of Pipe W and Pipe X =50 mm • Diameter of Pipe Y = 30 mm • Diameter of Pipe Z = 20 mm The velocity in meter per second through Pipe X is Blank 1 m/s. ***EXPRESS YOUR ANSWER in TWO (2) DECIMAL PLACE and DO NOT PUT UNITS*** T-1 Pipe Y 7m 4m Pipe Pipe W Pipe Z

Water flow from a large tank (T1) through a pipe Pipe X which splits into two smaller pipes, which discharges and flow out freely on Pipe Y and Pipe Z on as shown on the figure below. • Diameter of Pipe W and Pipe X =50 mm • Diameter of Pipe Y = 30 mm • Diameter of Pipe Z = 20 mm The velocity in meter per second through Pipe X is Blank 1 m/s. EXPRESS YOUR ANSWER in TWO (2) DECIMAL PLACE and DO NOT PUT UNITS T-1 Pipe Y 7m 4m Pipe Pipe W Pipe Z

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.1P: 7.1 To measure the mass flow rate of a fluid in a laminar flow through a circular pipe, a...

See similar textbooks

Similar questions

choose the correct answer Water flows horizontally from section 1 to section 2. If the area of section 1was 3 times area of section 2 then the velocity of section 1(v1) will be: * a) v1= v2 b) v1=1/2 v2 c) v1= 1/3 v2 d) v1= 1/4 v2 E)none of all above
Pumps: Two geometrically similar pumps are running at the same speed of 1000 rpm. One has the impeller diameter of 0.4 m and discharge of 30 liters/sec against a head of 20 m. If the other pump gives half of the discharge rate, then determine the head and diameter of the second pump. Answer: D=0.317 m, H=12.6 m
Water flows through a horizontal pipe of cross sectional of 20 cm2. Atone section, the cross sectional area is 4 cm2. the pressure difference is29.4 psi. How many cubic meters of water will flow out of the pipe in 1min? (can you show the diagram or illustration if possible. thank you!) Choices: a. 0.008 b. 1.208 c. 0.493 d. 0.0185
Complete Solution please, thanks. 3. A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of-assume values with decimals between 3 to 4 m per second- enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack.
Find an expression for the velocity of water leaving the sprinkler. Find an expression for the gauge pressure at point A, a distance L1, upstream of the narrow pipes. Express the answer in terms of the flowrate, Q. The inner diameter of the first segment of the pipe is d1=10mm, the inner diameter of the second set of pipes is d2=1mm, with N=25. The flowrate through the sprinkler is Q=0.2 L/s. Flow in pipes typically becomes turbulent when the Reynolds number exceeds 2000. Comment on the accuracy of the assumption that the flow could be treated as laminar everywhere. May be assumed water has a density of 1000kg/m^3 and a viscosity of 1mPa s.
In a 250 mm diameter pipe, oil discharges through a sharp crested round orifice, 100 mm in diameter. If the coefficient of contraction (Cc) and coefficient of velocity (Cv) are 0.63 and 0.98, respectively. SG of oil is 0.86. Determine the following: a) discharge from the orifice, (L/s) given that: coefficient of orifice, Co= Cc x Cv b) diameter of jet (mm) given that: Cc = Ajet/Atheo c) actual velocity in the jet, (ft/s) Note: Maintain 3 decimal places on partial and final answers.
A two dimensional, steady, incompressible and potential flow field of water (ρ=1000 kg/m3) is given with velocity components u and v. If the velocity component, u is given as u=1,5xy m/s with the magnitude of maximum pressure in the field as 42156 Pa. a) At x=+1 m and y=+2 m point, what is the magnitude of the velocity component v (in m/s)? (Please use 2 decimal digits in your answer) b) At x=+1 m and y=+2 m point, what is the magnitude of dynamic pressure (in Pa)? (Please do not use any decimal digit in your answer) c) At x=+1 m and y=+2 m point, what is the magnitude of static pressure (in Pa)? (Please do not use any decimal digit in your answer)
A 124-mm-diameter pipe enlarges to a 139-mm-diameter pipe. At section 1 of the smaller pipe, the density of gas in steady flow is 221.912 kilograms per meter cube, and the velocity is 23 meter per second; at section 2 of the larget pipe, the velocity is 15 meter per second. Find the density (in kilograms per meter cube) of the gas at section 2. Round off to three decimal places.
Water flows smoothly through a pipe with various circular cross-sections of diameters 2D, 6D, and D`, respectively. a.) What is the ratio of the speed in section 3 to the speed in section 1? V3/V1= b.) In which section is the pressure largest? Choose the best answer. a.) They are the same b.) Section 1 c.) Section 2 d.) Section 3
A pipe AB carries water and tapers uniformly from a diameter of 4" at A to 8" at B over a length of 6 ft. Pressyre gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 14.5 psi) Illustrate the problem before answering the following questions: (a)determine the flow, in ft^3/s through the pipe at C neglecting all lossess. (1 bar = 14.5 psi) (b)determine the pressure in bars, recorded at C neglecting all losses.
At a hydraulic plant the propeller type turbine are rated at 48,000 HP at 82 rpm under a 14 meters head, the diameter is 7 meters, for a geometrical similar turbine to develop 36,000 HP under a 11 meters head. After resolving the percentage change in probable flow, determine the following: (A) What diameter, in meter, of the impeller to be used? (B) What is the speed, in RPM, should be used?
An incompressible fluid is flowing through a pipe that is gradually tapering in size by 0.01 m2/m. What is the change in velocity per meter where the pipe is 0.4 m2 in cross section and the velocity is 30 m/s. Express your answer in two decimal places.