Water flows from a large reservoir at the rate of 1.20 ft/s through a pipe system as shown in Tigure below. Calculate the total amount of energy lost from the system because of the valve, elbows, the pipe entrance, and the fluid friction. 12 ft 13 tt 3-in diameter Floy

Water flows from a large reservoir at the rate of 1.20 ft/s through a pipe system as shown in Tigure below. Calculate the total amount of energy lost from the system because of the valve, elbows, the pipe entrance, and the fluid friction. 12 ft 13 tt 3-in diameter Floy

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter12: Electric Current And Related Variables In Engineering

Section: Chapter Questions

Problem 23P

See similar textbooks

Related questions

Q: A pump is tested as shown in figure for water and for one setting of the valve in the discharge…

A: Pump is a device that moves liquids, gases and sometimes slurries from lower elevation to higher…

Q: Q5) Using a system similar to that shown in figure, compute the required air pressure above the…

A: Figure is as shown

Q: Figure shows a lawn sprinkler with unequal arms. The jets issuing out of Example 7.12 40 cm 60 the…

Q: Problem 6-76 Oil is flowing upward through a Venturi meter as shown Assuming discharge coefficient…

Q: The double pulley shown weighs 15 kg and has a centroidal radius of gyration of 160 mm. Cylinder A…

Q: Determine the discharge through three new cast iron pipes, having the diameters as shown in the…

A: Three cast iron pipes are connected in series with frictional loss given and it has been asked to…

Q: Water is flowing through a venturimeter shown. The difference in pressure between Point 1 (D = 4cm)…

Q: A 70-mm-diameter suction pipe leading to a pump, as shown below, carries a discharge of 0.05 of oil…

Q: Calculate the magnitude of the clockwise couple M required to turn the 50-kg cylinder in the…

Q: Water is flowing through a venturimeter shown. The difference in pressure between A (D = 5cm) and B…

A: Given data in question Diameter Head loss To find out Velocity head at A

Q: From the figure shown, the tank contains oil having s specific gravity of 0.80. Oil flows at a…

Q: Water flows out of a hemispherical tank at the constant rate of 18 cu cm per min. If the radius of…

Q: Calculate the pressure difference between the water pipe (point A) and the oil pipe (point B) that…

Q: Water is flowing in a 300 mm pipe a pitot tube is connected to determine the velocity, if the gauge…

A: Find velocityv=2ghh=xshgsw-1h=0.075m13.61-1h=0.945m

Q: The internal diameter of the pipe system shown in the figure is 15.24 cm. The exit nozzle diameter…

A: Given :

Q: Consider a 1.2-m wide inclined gate of negligible weight that separates water from another fluid.…

Q: For the system shown in the given figure calculate the height H of oil at which the rectangular…

Q: Q2. A venturi meter of 15 cm inlet diameter and 10 cm throat is laid horizontally in a pip to…

A: Diameter of inlet (d1) = 15cm = 0.15 m Area of inlet (A1) = Π(d1)2/4 = Π*(0.15)2/4 = 0.01766 or…

Q: The closed cylinder shown is filled with water to a depth of 100mm and rest with air. What…

Q: Pipe Length Diameter 1 947mm 250mm 583mm 275mm 3. 1026mm 180mm

Q: If the given system is released from rest in the position shown, calculate the velocity of hits the…

Q: The double pulley shown weighs 15 kg and has a centroidal radius of gyration of 160 mm. Cylinder A…

Q: Calculate the value of h, in meters, in the Venturi meter shown in the volumetric flow rate of water…

Q: 5. The horizontal pump in the Figure discharges 30°C water at 40 m'/h. Neglecting losses, what power…

Q: Water is flowing in a 40 mm diameter uPVC pipe as shown in the figure. The total pipe length is 16…

A: Given: Total pipe length = 16 m Volume of water tank (from empty) = 500 liter Difference in…

Q: plot the relationship between the total energy line and hydraulic gradient line Vs distance from the…

Q: It is desired to pump 390 liters per second of water from a stream to a pool as shown in the figure…

A: Q = 390L/s = 0.39m3/s

Q: ) For the system in figure, the atmospheric pressure is 101.33 kPa and the absolute pressure at the…

Q: Q1. A rectangular water tank of length 10m and width 6m has a free surface 15m above a 300mm…

A: Given data Cross sectional area Length Diameter Coefficient of discharge

Q: A pump is tested as shown in figure for water and for one setting of the valve in the discharge…

A: A pump is a device that moves liquid, gases and sometimes slurries by mechanical energy converting…

Q: The pump in the figure shown discharges water at 34.00 L/s. Neglecting losses and elevation changes,…

A: Applying Bernoulli's principle at the section 2 just at the inlet of pump and outlet of pump. Power…

Q: Q1) Water flows from a pressurized tank (in figure below), through a 10.0 cm diameter pipe, exits…

A: Bernoulli's equation has to be used for determining pressure in tank.This equation gives the…

Q: The flow rate of water through the pipe system shown in the figure is 30 lit/s under the total head…

A: Step 1

Q: A closed cylindrical tank 2m in diameter and 5m tall has 1.5m of oil (SG = 0.80), 0.5m of an unknown…

Q: 4. Based on the schematic view of the system provided below: a) find the pressure head, hp, that…

Q: A closed tank contains 20 m deep water. A hose is connected as shown such that the nozzle (diameter…

Q: Q1) Water flows from a pressurized tank (in figure below), through a 10.0 cm diameter pipe, exits…

Q: Determine the natural frequency of the system shown in the figure. The beam is of negligible mass.…

A: We know, stiffness of spring, k=Wδδ=Wkwhere,W=loading,δ=deflection Frequency of free…

Q: QI Figure Q1 shows a canon firing a shell at 50° from the slope, from a height of 200m. It was…

Q: 6. From the water tank shown in the figure, water is drawn by siphoning, where you find the flow…

Q: Calculate the minimum power of the pump which will send the jet of water over the wall shown in…

Q: Q3) for the symmetrical fixed vane show in figure below, if the velocity of jet is V area of the jet…

A: Introduction : The kinetic energy of a jet of water ejected from a nozzle is determined by its…

Q: QI) Water flows from a pressurized tank (in figure below), through a 10.0 cm diameter pipe, exits…

Q: Water flows in a pipe, a 30mm x 25mm reducer is connected to change the speed of the water, if the…

Q: fluid is flowing in a 6-in diameter pipe at a pressure of 3.63 in2 with a velocity of 9.67 E. As…

Q: A tank in circular section is 10 m high. It takes 8.4 min to empty the tank through a hole at the…

Q: PS 7 Kerosene Air B 10 сm cm 21cm 9cm cm Benzene Mercury Water

Q: 11. The velocity through a pipe of diameter 0.5 meters is 7.5 meters/sec. Total head (including…

A: given- dia of pipe d=0.5 mvelocity v=7.5 m/shead difference h=4.5 m

Q: A closed tank contains 20 m deep water. A hose is connected as shown such that the nozzle (diameter…

Concept explainers

Electric Current, Voltage and Electric Power

The term electric current is the flow of electrons or electric charges. The drift of electrons is proportional to the amount of voltage or potential difference applied. The more is the voltage, the more will be the electron drift. The amount of electric current a circuit possesses is proportional to the density of electrons or electric charge.

Question

100%

Water flows from a large reservoir at the rate of 1.20 ft/s through a pipe system as shown In
Tigure below. Calculate the total amount of energy lost from the system because of the valve,
elbows, the pipe entrance, and the fluid friction.
12 ft
13 t
3-in
diameter
Floe
2.

Expert Solution

Step 1

To calculate the amount of energy loss (H_L)-

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Electric current, voltage and electric power

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water in pressurized cylindrical tank 40 ft. in diameter discharges into the atmospherethrough a nozzle 4 inches in diameter. Neglecting friction, and assuming unsteady flow;find the time required for the water in the tank to drop from a level of 50 ft. above thenozzle to 2 ft. above it if the tank is under constant gauge pressure of 1 atm. State anyassumptions.
pump discharges 1129.52 kg/min of water to a vertical tank (10ft dia by 15 ft height). Find the total time (in min) the tank will be 3/4 full.
Water flows through the turbine shown at a rate of 0.386 m3/s. The pressures at points A and B are 161.2 kPa and -19.6 kPa, respectively. What is the electrical power generated by the turbine if it is 85% efficient?
A centrifugal pump delivers water at the rate of 50 kg/s. The inlet and outlet pressures are 2 bar and 6.2 bar respectively. The suction is 2.2m below the centre of the pump and delivery is 8.5m above the centre of the pump. The suction and delivery pipe diameters are 200mm and 100mm respectively. Determine the capacity of the electric motor considering the efficiency of motor as 80% to run the pump.
Design the chilled water pipe system shown in the figure and calculate the power of the pump. Take the pressure loss in each elbow as 250 Pa. * 50 Lit/min 30 Lit/min 40 Lit/min
Determine the natural frequency of the system shown in the figure. The beam is of negligible mass. Given: M=25 kg, E=200 GPa, I=5x10-7 m4, and k spring =5 kN/m.
Fluid mechanics, nozzle problem: Water at 15oC flows through the nozzle that contracts from a diameter of 10 cm to 2 cm. The exit speed, v2= 25m/s and atmospheric pressure prevails at the exit of the jet. Calculate the pressure at section 1 and the force required to hold the nozzle stationary.
The volumetric flow through the pump in the figure is Q = 0.014 m3 / s. The fluid being pumped is oil with specific gravity SG = 0.86. Losses in the system are caused by the check valve and friction in the pipeline and were estimated at HLT = 1.86 m col of water. Other data available are: PA = -28 kPa (vacuum), PB = 296 kPa (man), ZB = 1 m, DA = 7.62 cm, DB = 5.08 cm. Calculate the POWER in kW that the pump transmits to the oil. Bomba = pump flujo = flow/flux válvula de verificación = check valve
solve for the flow rate in the venturi meter. C=0.815 use 3 decimal places
pump discharges 1129.52 kg/min of water to a vertical tank (10ft dia by 15 ft height). Find the total time (in minutes) the tank will be 3/4 full.
Note: If you got answer other than options, please leave it question. A nozzle discharges 155lit/sec with a velocity of 35m/s. The entire jet strikes a vane moving in the same direction as the jet with a velocity of 20m/s. Compute the Force exerted on the vane.
HYDRO EXPERIMENT NO.3 4. A 100 mm diameter orifice discharges 45.34 li/s liquid under a head of 3.60 meter. Using a vernier caliper, the diameter of the jet at the vena contracta is found to be 87 mm. Calculate Cv, Cd, and Cc.