Water flows inside a pipe as shown in Fig. (3). At the lower point, the pipe diameter is 5 cm and pressure is P1 = 18 kPa. At another point y 0.3 m higher, the pipe diameter is 2 cm and pressure is P2 = 10 kPa. Calculate: %3D %3D %3D (a) the speed of flow in the lower and upper sections. (b) the volume flow rate through the pipe.

Water flows inside a pipe as shown in Fig. (3). At the lower point, the pipe diameter is 5 cm and pressure is P1 = 18 kPa. At another point y 0.3 m higher, the pipe diameter is 2 cm and pressure is P2 = 10 kPa. Calculate: %3D %3D %3D (a) the speed of flow in the lower and upper sections. (b) the volume flow rate through the pipe.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 6.0 cm diameter horizontal pipe gradually narrows to 4.5 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 33.5 kPa and 22.6 kPa, respectively. What is the volume rate of flow?
In a horizontal pipe water flows at a rate of 9.1 L/s. Here, the pipe has two sections, one with a diameter of 10.16 cm and the other with a diameter of 5.08 cm, with a gradual smooth reducing section. In this case, a mercury manometer is used to measure the pressure difference. If friction is negligible how would I find the differential height of mercury between the two sections? If the manometer on the 5.08cm pipe section was replaced with a pitot tube how would the reading change? any help would be deeply appreciated
The diameter of pipe carrying water changes gradually from 20mm at A to 450mm at B. A is 4.57m lower than B. What will be the difference in pressure,in N/mm2, between A and B, when 0.176cu.m/s is flowing loss of energybeing neglected?
In fluid flow equations, the variable p/ϒ is called A. Pressure Head B. Velocity HeadC. Static Head D. Total Head
A horizontal water pipe diameter 15 cm converges to 7.5 cm diameter. If the pressures at the two sections are 4 kg/cm2, and 1.5 kg/cm2 respectively, calculate the flow rate of water.
The water is flowing through a pipe having diameters 40 cm and 21 cm at sections land 2 respectively. The rate of flow through pipe is 45 litres/s. The section 1 is7 m above datum and section 2 is 4.5 m above datum. If the pressure at section 1 is 35 N/cm2. find the following by neglecting losses: (1) Area of cross section of section1(unit in m^2)? 2)Area of cross section of section2 (unit in m^2)? 3)velocity head at section 1 (unit in m) 4)velocity head at section 2 (unit in m) ? 5) difference in datum head (Unit in m)? 6) Pressure head at section 1 (Unit in m)? 7)pressure at section 2 (unit in N/m)?
Air flows through a compressor under steady flow conditions. At suction V1=0.75m3/kg, v1=30m/s At discharge: V2=0.25m3/kg, v2=40m/s.. Determine the diameter ratio of the discharge pipe to that of the suction pipe. (Ans. 1:2)
A jet of water issues from a kitchen faucet and falls vertically downward at a flow rate of 34 mL/s. At the faucet,which is 35 cm above the sink bottom, the jet diameter is 1.5 cm. Determine the diameter of the jet where it strikes the sink.
Water enters a shower head through a pipe of internal radius r = 6.4 mm, and leaves through 30 small holes, each of radius r1 = 0.08 mm. When the faucet is opened, the water moves in the tube at a speed of 90 cm/s. What is the volumetric flow of the shower head in liters per second?
Water moves through a constricted pipe in steady,ideal flow. At the lower point shown in the figure, thepressure is P1 = 1.75x104Pa and the pipe diameter is6.00 cm. At another point y = 0.250 m higher, thepressure is P2 = 1.20 x 104Pa and the pipe diameter is3.00 cm. Find the speed of flow (a) in the lower sectionand (b) in the upper section.(c) Find the volume flow rate through the pipe.Ans. ( (a) 0.638 m/s (b) 2.55 m/s (c) 1.80 x 10-3 m3/s ).
A two storey building has two faucets, one in the basement and one in the firstfloor. The maximum water (ρ = 1000 kg/m3) velocity at the basement faucet, when the first floor faucet is closed, is 13 m/s. The faucet diameter is 1.5 cm.Neglect all losses. What would be a maximum height (from the basement floor) for a faucet,to still get a maximum exit velocity of 6 m/s?
Consider the incompressible flow of water through a divergent duct, where the inlet has a velocity & section area of 5 ft/s & 10 ft2. If the exit area is 5x the inlet area and the density of water is 62.4 lbm/ft3, solve for the pressure difference. (Please type answer no write by hend)