With FBD Water flows through a horizontal pipe at a velocity of 50 fps. Owing to the pipe graduallyexpanding to a larger size, the velocity decreases to 35 fps, what is the difference between thepressures at two points, one in each size of the pipe?

Answered: Image /qna-images/answer/e05b487a-f42e-4f22-9b7e-668eefe332b4.jpg

Answered: Water flows through a horizontal pipe…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows from a cylindrical pipe of diameter 6-cm into another cylindrical pipe of diameter 3-cm. If the water exhibits a velocity of 10 m/s in the second pipe, what was the velocity in the first?
A 30 cm diameter pipe, conveying water, branches into two pipes of diameters 20 cm and 15 cm respectively. If the average velocity in the 30 cm diameter pipe is 2.5 m/s, find the discharge in this pipe. Also, determine the velocity in 15 cm pipe, if the average velocity in 20 cm pipe is 2 m/s.
Water flows through a rubber hose 2 cm in diameter at a velocity of 4 m/s. (a) What must be the diameter of the nozzle in order that the water emerge at 16 m/s? (b) What is the rate of flow in cu.m per minute?
2. A 50cm diameter pipe, conveying water, branches into two pipes of diameter 30cm and 20 cm respectively. If the average velocity in the 50 cm diameter pipe is 2.5 m/s, find the discharge in this pipe. Also determine the velocity in 20 cm pipe if the average velocity in 30 cm diameter pipe is 1.5 m/s.
The diameter of pipe carrying water changes gradually from 20mm at A to 450mm at B. A is 4.57m lower than B. What will be the difference in pressure,in N/mm2, between A and B, when 0.176cu.m/s is flowing loss of energybeing neglected?
The rectangular above is a control volume. Flow 1 is 3.1 slugs/sec while flow 2 is 6.3 slugs/sec. The fluid has density 2.7 slugs/ft3. Determine the volumetric flow rate of flow 3 in ft3/sec.
Air flows through a compressor under steady flow conditions. At suction V1=0.75m3/kg, v1=30m/s At discharge: V2=0.25m3/kg, v2=40m/s.. Determine the diameter ratio of the discharge pipe to that of the suction pipe. (Ans. 1:2)
Air is flowing steadily through a converging pipe at 40°C. If the pressure at point 1 is 50 kPa (gage), P2 = 10.17 kPa (gage), D1 = 3D2, and atmospheric pressure of 96.27 kPa, the average velocity at point 2 is 22.0 m/s, and the air undergoes an isothermal process, determine the average speed, in cm/s, at point 1. Round your answer to 3 decimal places.
A steady stream of water travels through an enclosed tank, as seen in the illustration. At section 1, D1 is equal to six centimeters, and the volume flow equals one hundred m3/h At section 2, the average velocity is 8 meters per second, and D2 equals 5 centimeters. If D3 is equal to 4 centimeters, then (a) what is Q3 in m3/h and (b) what is the average V3 in m/s?
Two pumps (Pump A and B) have performance curves which can be approximated by the following equations: H_A = 340 - (1.2(Q^2)), in feet H_B = 360 - (2.5(Q^2)), in feet where Q is in ft^3/s. If pumps A and B were to operate in parallel as depicted in the figure below, at what head (in ft.) should either pump be operated?
The pressure loss p in a pipe is related to the flow rate Q by the equation P = KQ^n, where K and n are constants. If K = 190 x 10³determine the value for n when a flow rate of Q = 0.04 m³/s causes a pressure loss of 180 Pascals.
A closed vessel contains water up to a height of 2 m and over the water surface there is air having pressure 8.829 N/cm^2 above atmospher. At the bottom of the vessel there is an orifice of diameter of 15 cm. Find the rate of flow of water from orifice. Take Cd=0.60. (WITH FREE BODY DIAGRAM) CHOICES: a.115.75 L/s b.125.75 L/s c.155.75 L/s d.135.75 L/s

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Water flows through a horizontal pipe at a velocity of 50 fps. Owing to the pipe gradually banding to a larger size, the velocity decreases to 35 fps, what is the difference between the Ssures at two points one in each size of the pine?