Water flows through the pipe at A at 300 kg/s, and then out the double wye with an average velocity of 3 m/s through B and an average velocity of 2 m/s through C. Determine the average velocity at which it flows through D.

Water flows through the pipe at A at 300 kg/s, and then out the double wye with an average velocity of 3 m/s through B and an average velocity of 2 m/s through C. Determine the average velocity at which it flows through D.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A fan discharges 265 cu.m/min of air through a duct of 92 cm in diameter against a static pressure of 0.022 m of water. The fluid density is 995 kg/cu.m., the air temperature is 29°C and the barometric pressure reading is 730 mm Hg. If the power input to the fan is measured 3.5 hp, what are the total and static fan efficiencies?
Aiming a 1.69 in diameter garden hose straight up, forms a “bubbler fountain” that you could easily drink from (but you shouldn’t because of bacteria, etc.). The water flows out the hose and down the sides. If the water has a density of 63.1 lbm/ft^3 and a viscosity of 0.0119 g/cm*s, what is the thickness of the water film (df) (in cm) if the flow rate of water is 6.42 in^3/s? For simplicity, assume the film is thin enough that you can use rectangular coordinates.
please answer A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle β2 is 158° and the radial velocity at the outlet Cr2 is 4 m/s. Assuming radial flow at inlet, draw the theoretical outlet velocity diagram and calculate the various velocities and angles.( A)What is the theoretical head Ho, in meters, assuming that the circulatory flow coefficient η∞ = 1.,(B)In the preceding example; assume a deviation of 10° applied to β2 due to circulation after the modern theory. The flow is 30 lit/s. After drawing/illustrating the velocity diagram, find the theoretical head Ho, in meters, assuming radial flow at inlet, neglecting the deviation in inlet velocity diagram. (c)Assuming that the mechanical efficiency ηmech = 0.95, the hydraulic (or manometric) efficiency ηman = 0.8, find the required break horsepower to drive the pump.
5. The total head of a fan is 185 m and has a static efficiency pressure of 210 mm of water gage.What is the velocity of air flowing if the density of air is 1.15 kg per cubic meter? 8. A coal fired steam boiler uses 3000 kg of coal per hour. Air required for combustion is 15.5 kg ofcoal at barometric pressure of 98.2 KPa. The flue gas has temperature of 285 degree Celsiusand an average molecular weight of 30. Assuming an ash loss of 11% and allowable gas velocityof 7.5 meters per second. Find the diameter of the chimney 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of…
Vortex shedding can be used to design a vortex flowmeter(Fig. 6.34). A blunt rod stretched across the pipe shedsvortices whose frequency is read by the sensor downstream.Suppose the pipe diameter is 5 cm and the rod is acylinder of diameter 8 mm. If the sensor reads 5400 countsper minute, estimate the volume flow rate of water in m 3 /h.How might the meter react to other liquids?
Final Ans: Discharge: 0.330 cfs Diameter of Jet: 1.587 in. Mean Velocity: 24.0 ft/sec Lost head: 0.56 ft
Nitrogen gas under a pressure pn = 15 psig is used for pumping kerosene at 25°C (density = 816 kg/m3, viscosity = 1.81 cP) through an elevation increase of 6 m. If there is an effective length of 45 m of nominal 2-in. schedule No. 40 pipe (commercial steel) between the two tanks, what is the flow rate of kerosene? Neglect exit kinetic-energy effects.
Air flows through a duct at 2,700 cubic feet per minute (CFM). After several feet and a few vents, the air-flow decreases to 1,890 CFM. What is the percent drop that has occurred? (Simplify your answer completely.)
A fire hose has an inside diameter of 6.5 cm. Suppose such a hose carries a water flow of 40.5 L/s starting at a gauge pressure of 1.68 × 106 N/m2 . The hose discharges through a nozzle having an inside diameter of 3.4 cm. Take the viscosity of water to be 1.005 × 10-3 (N/m2)⋅s dh = 6.5 cmdn = 3.4 cmP = 1.68 × 106 N/m2Q = 40.5 L/s a. the Reynolds number, NR, for flow in the fire hose to show that the flow must be turbulent, with NR≥ 3000. b. Calculate the Reynolds number, NR, for flow in the fire hose and nozzle to show that the flow must be turbulent, with NR≥ 3000.
A Kaplan turbine has the following specifications: H =25 ft., N=400 rpm; power = 650 hp. If the efficiency of the unit is 90%, estimate (a) the flow rate, (b) approxi-mate diameter of the runner, (c) turbine setting to avoid cavitation if the location is at sea level, and (d) turbine setting to avoid cavitation if the location of the unitis at an elevation of 5000 ft. The local temperature is 60°F.Ans: (a) Q=254 cfs; (c) Hs=5.8 ft.; (d) 0.12 ft.
1. You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. In the design specifications given, if the actual measurement of power via the substation amounts to exactly 530kW and given that the windspeed is off by 0.05m/s, what could have been the error in the measurement of diameter? Your answer must be in 3 decimal places and in correct signs and measurement. Show complete solution in paper.
Air at 60∘C∘C flows through the very wide duct. Suppose that L� = 150 mmmm . ν� = 18.9(10−6−6) m2/sm2/s. (Figure 1) Determine the required dimension a� of the duct at x� = 4 mm so that the central core flow velocity maintains the constant free-stream velocity of 0.5 m/sm/s. Express your answer to three significant figures and include the appropriate units.