Water flows with a velocity of 3 m/s at a depth of 1.5 m in a trapezoidal channel with a 2-m base and sides sloping at 45o . It empties into a circular pipe and flows at 2 m/s. What is the diameter if the pipe flows full?

Water flows with a velocity of 3 m/s at a depth of 1.5 m in a trapezoidal channel with a 2-m base and sides sloping at 45o . It empties into a circular pipe and flows at 2 m/s. What is the diameter if the pipe flows full?

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter16: Highway Drainage

Section: Chapter Questions

Problem 13P

See similar textbooks

Related questions

Q: Problem-8. In a Marshall sample, the bulk specific gravity of mix and aggregates are 2.324 and 2.546…

A: Given- Bulk specific gravity of mix Gm=2.324, Bulk specific gravity of aggregate =2.546, 5% of…

Q: 3.5.2 (revised). A wrought iron pipe, 1.50 feet in diameter and 100 feet long, carries 12 cfs…

Q: Solve the following problems using the figure. 1. Calculate the ultimate settlement of the clay…

A: Given data: Unit weight of fill=118 lb/ft3 Unit weight of sand=109 lb/ft3 Unit weight of saturated…

Q: 5 In the figure shown, if the index contour "A" is equal to 150 m, and the scaled horizontal…

Q: 30kN/m. the beam is 12 meters long and is laterally supported at the midspan, and A572 Gr.50 steel…

A: Solution is as given below

Q: In a simply supported beam of 10 m span having udl of 8 kN/m, the maximum Bending Moment shall be 80…

A: Given, A simply supported beam, L= 10m Udl= 8kN/m To find :- maximum bending moment

Q: An irregular structure in Fig. BES SRB 003 is subjected to multiple forces and a couple as shown.…

A: To find distance of resultant form x axis wrt point A

Q: Find the work done in moving crate upto distance of 5 m with help of applied force is 11 N

A: Given data : The applied force magnitude F=11 N The distance moved after force applied d=5 m…

Q: P = 35 Utilize Cantilever Method 2P kips 2P kips- Moment at column A a. 106 kft.cw b. 148 kft.ccw c.…

Q: A surface water treatment plant operates round the clock with a flow rate of 35 m³/min. The water…

A: Given- Discharge- Q=35 m3/min, Alum dose=25 mg/L, It is needed to find the alum quantity required…

Q: When completing the vacuum filtration step which type of tubing is best? (Answer Choices - only pick…

Q: Designation Serial size 457x191 67 Calculate the design tension resistance of the 457 × 191 × 67 UB.…

A: Given: Section: 457 x 191 x 67 UB Ag = 85.51 cm2 S275 grade: Fy = 275 N/mm2

Q: 3. A steel beam is use to carry a uniform load of 25 kN/m over a span of 6 m. The left support must…

Q: 2 In the figure shown, what does "D" represent? E B

A: Contours are imaginary lines showing elevation of points and connecting points of equal elevation.…

Q: Buoyancy 4Q. A balloon uses hot air to provide its lifting capability. Prior to its release it is…

A: In this problem we have to asked find the initial weight in hot air. And buoyant force and cable…

Q: 4. Determine the deviation under the load X with respect to the tangent at A 5. Determine the…

A: Given: Required: deviation under the load X with respect to the tangent at A deviation under the…

Q: 3. The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the largest vertical…

Q: The time period of rolling of a ship of weight 29430 kN in sea water is 10 seconds. The centre of…

A: Given Time period T=10 sec, Distance between centre of buoyancy and centre of gravity BG=1.5 m,…

Q: Find the spring force if EI= 2*108 kN.cm² and the Flexibility of the spring P = 0.125 cm/kN. 2 kN/m…

Q: Instruction: Determine the stability and determinacy of the following beams, frames, and trusses.…

Q: A 1,394-lb force is applied to a rotating tool steel bar at a frequency of 3000 cycles/minute. The…

A: Given data:- The given applied force, F=1394 lb The cycle applied per minute,=3000 cycles/minute The…

Q: Problem 3-108 The section of a concrete dam is shown in the figure. Concrete weights 23.5 kN per…

Q: beam, determine the (a) shear at C and (b) moment at C. Determine the area for the moment diagram of…

A: as we know, in conjugate beam free support of real beam is become fixed and vice versa. loading:-…

Q: PROBLEM 2 Determine the forces in members GB, GF, GC and BF by the: a). Method of Joints b). Method…

A: Find out 4 member forces using methid of joints and sections. Load and truss dimensions are given.

Q: El is Constant (Assume El = 1 kN-m²) B kN/m 7 m 14. Determine shear at C for the equivalent…

A: Given: Required: shear at C for the equivalent conjugate beam moment at C for the equivalent…

Q: A cantilevered beam has a distributed load (w) of 5035N/m acting down on it and along its entire…

A: We will be using the method of superposition to solve the given problem. The Deflection at the point…

Q: A rectangular gate 1.5m by 3.5m is inclined 60o with the horizontal. The top of the gate is…

Q: 4 2m 3rd day 8 kr/m 3m of Im

Q: 2Q. A flow field is defined by u = 2y, v=xy. Derive expressions for the x and y components of…

A: Given: 1. u=2y2.v=xy3.(x,y)=(2,3) To find: 1. Velocity= V2. Accleration =a Unit to use: In terms of…

Q: A vertical rectangular sluice gate at the bottom of the dam is 0.60m wide and 1.8m high and exposed…

Q: In the figure shown, if the index contour "A" is equal to 150 m, and the scaled horizontal distance…

A: From the contour map,Index contour A=150 mIndex contour C=100 mHeight difference between A and…

Q: The 5m radius cylindrical gate shown is 8m long into the paper. If 0 = 60°, determine the location…

Q: From the frame loaded as shown. Solve the following if P = 15 Use Cantilever Method. 2P kips 2P…

Q: Int em 1 For the beam show, draw the influence lines for 1. A shear just of A. 6. shear just to the…

Q: 2Q. A flow field is defined by u = 2y, v=xy. Derive expressions for the x and y components…

Q: Hydrostatic forces on curved surface 5Q. The curved dam shown in the figure is 50 m wide into the…

Q: Calculate the x-component of B (in N, round-off to 2 decimal places) of the loaded frame. D C 120…

Q: v - [80-²k); Q- On a section of a highway the speed-density relationship is linear and is given by…

A: Given data- Speed density relation- v=80-23k, v=free mean velocity, k=jam density, To Find- The…

Q: The uniform bar AB of weight W is leaning against a vertical wall. The coefficient of static…

A: ###Determination of smallest angle at which bar remain at rest###

Q: The 742-N force is applied to the 117-kg block, which is stationary before the force is applied.…

Q: 26. A soil has a liquid limit of 40% and plasticity index of 20%. The plastic limit of the soil will…

A: Given data: Liquid Limit,WL = 40% Plasticity index, Ip=20% Plastic Limit, W p of the soil =?

Q: Problem 3-108 The section of a concrete dam is shown in the figure. Concrete weights 23.5 kN per…

Q: A 7-meter simple beam is loaded with a varying load that varies from 0 kN/m to 40 kN/m applied at 1…

A: Given:- The length of the simply supported beam = 7 m The varying load varies from 0 kN/m to 40…

Q: Determine whether each of the trusses below are internally determinate, indeterminate, or unstable.…

A: Finding internal indeterminacy

Q: The 36-kg homogeneous smooth sphere rests on the 26° incline A and bears against the smooth vertical…

Q: A 48-in. boom is held by a ball-and-socket joint at Cand by two cables BF and DAE, cable DAE passes…

Q: Calculate for the BB (In terms of El) (TWO DECIMAL PLACES) DISREGARD SIGN CONVENTIONN IN INPUTTING…

A: Given, Beam loading diagram To find : Slope at point B

Q: -3 B 9' lb

Q: Q2. An embankment is being built of a soil whose effective stress shear strength parameter c' and '…

Q: Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support…

A: Reference : Structural Analysis, Forces in members. Given : Two loads and angle at A, B , C and D…

Concept explainers

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Time and time related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the depth of water in a trapezoidal channel with z = 2.0 and carrying 2.5 cubic meter per second of water flow? The channel’s bottom width is 2.5 m and the velocity of flow is 0.9 m/s.
Water flows in a rectangular channel with a velocity of 2 m/s and depth of 4 m. -Find the critical depth of the flow.
A trapezoidal channel with side slope of 1:1 has a bottom width of 2 m. At a critical depth is 2.24 m, what is the velocity of now?
. For a rectangular channel with depth 1.2 m and 1.8m wide S=0.002 and n=0.012 ,what would be the velocity of the flow?
Water flows at a velocity of 3.0 m/s and a depth of 5.0 m in a channel of rectangular section 3.0 m wide. There is a smooth upward step of 2.5 m in the channel bed. What expansion in width must take place for the upstream flow to be possible as specified?
A welded steel channel (Manning n = 0.015) is rectangular in cross-section, being 1.55m wide, and is laid on a slope 1 in 500. Water flows in the channel with a depth of 1.28m, what is the volumetric flow rate?
Water flows in a trapezoidal channel at a depth of 40cm and with a velocity of 10m/s. An obstruction causes a hydraulic jump to be formed. What is the depth of flow downstream of the jump? The bottom width of the channel is 5m, and the side slopes are 1 vertical to 1 horizontal.
Need help asap. Water flows in a wide channel at q = 10 m³/s/m and a depth of 1.25 m. If the flow undergoes a hydraulic jump, Determine:
Water is flowing uniformly in a finished-concrete channel of trapezoidal cross section with a bottom width of 0.8 m, and trapezoid angle of 50 degrees (outer angle measured from the horizontal plane). If the flow depth is measured to be 0.52 m, determine the Hydraulic Radius. a. 0.540 m b. 0.298 m c. 1.065 m d. 1.362 m
Water flows in a long, 2.50 m wide rectangular channel at a uniform flow depth of 1.07 m and a uniform velocity of 1.68 m/s. The hump height is 0.75 m. a. Calculate the flow depths immediately before, on top of, and immediately after a smooth hump on the channel bed. b. Calculate the force exerted by the flow on the hump.
Water flows through an almost level channel 3 m wide at a rate of 12 m³/s. The depth gradually increases from 1 to 1.10 m over a length of flow of 5 m. Which of the following most nearly gives the head lost in meters?
Water in a rectangular channel flows into a gradual contraction section as indicated below. If the flowrate is Q = 0.7 m3 /s and the upstream depth is y1 = 0.6 m, determine the downstream depth y2.