Water is flouing. is to be pumpeol for 10o malory50 mm internal dliamekre pipe at the retein aof3:0kg ls. The Pipe is them raiscolverdicallylom.wherethe Secondl oeservoir issituated.the pumpefvieney of 60%,raqused? Tope jioujhnen of lommeniaf st el pipekas auwhatpouer uill se0:045 mm.

Answered: Image /qna-images/answer/412cd796-414b-4759-8fe6-166a7f0e6e35.jpg

Water is flowing is to be pumpel for 1000 m alory 50 mm intonal odameku pipe. at the rcete of 3:0kg ls. The Pipe is then raiscol vesetically lom.where the Seiondl riservoir is sitateol. if the pump kas au will be efriney of sequired ? Tope jroyghnen of ummendaf dt el pipe G0%, what pouer A 0:045 mm.

Water is flowing is to be pumpel for 1000 m alory 50 mm intonal odameku pipe. at the rcete of 3:0kg ls. The Pipe is then raiscol vesetically lom.where the Seiondl riservoir is sitateol. if the pump kas au will be efriney of sequired ? Tope jroyghnen of ummendaf dt el pipe G0%, what pouer A 0:045 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Throughof the system that showsof the figure circlesa flow rate of 100L/slight oil(s=0.72), which ispowered by apump it upsupplies apower of 5.0 kW andworks with a85% efficiency.determine the timegauge mmdifferential
The velocity of flow of water at the centre of tube is _______ when the head is 0.1m, η=8.9*10-3 dynes-s/cm2, γw=1 g/cm3, the length is 10m and the diameter is 20cm.Dont attempt wrong I will dislike
As a test to determine the effective wall roughness of an existing pipe installation, water at 10°C is pumped through it at the rate of 300 L/min. The pipe is standard steel tubing, 40 mm OD x 3.0 mm wall. Pressure gages located at 25 m apart in a horizontal nm of the pipe read 1235 kPa and 849 kPa. Determine the effective pipe wall roughness.
include a free body diagram Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet isA. 6.21B. 7.12C. 8.7D. 5.05
In Fig. the pipe entrance is sharp-edged. If the fl ow rateis 0.004 m3/s, what power, in W, is extracted by the turbine?
plzzzz help me with this one plzzz Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m3 ) is to be pumped through 50 m of pipe from lower reservoir to a higher reservoir at a rate of 0.2 m3/s. If the pipe is cast iron of diameter 12 cm and the pump efficient is =0.44%, the major head loss inside the pipe is ¼ of the velocity head what horsepower pump is needed? Hint: consider the abrupt expansion only as a minor loss.
is friction factor inversely proportional to the Reynold’s number in case of laminar flow in circular pipes?
Water flows at 20°C through a new cast iron pipe at a velocity of 4.2 m/s. The pipe is 400 m long and hasa diameter of 150 mm. Determine the head loss due to friction. Ans. 54.20 m (show the complete solution) Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet. E.g. (density, viscosity)Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness
Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 1.64 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.94 m.
Water in a partially filled large tank is to be supplied to the rooftop, which is 8 m above the water level inthe tank, through a 2.5 cm internal diameter pipe by maintaining a constant air pressure of 300 kPa (gauge) inthe tank. If the head loss in the piping system is 2 m of water, determine the discharge rate of the supply ofwater to the rooftop in L/s. Show complete solution
Q:/ Discuss the relation betwveen the head pressure and flow rate for the benefits of connecting the pumps in parallel ?
Water at 20°C flows in a 100-mm-diameter new cast iron pipe with a velocity of 5.0 m/s. Determine thepressure drop in kPa per 100 m of pipe and the power lost (in kilowatts) to friction.Ans. 314 kPa per 100 m, 12.36 kW per 100 m [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based on temperature available on the internet. E.g. (density, viscosity) . Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness}