Water is moving at a velocity of 4 m/s in a 1 m wide horizontal channel at a depth of 1 m. The roughness coefficient n=0.025. What is the distance downstream will the depth be increased to 1.1 meters? Select one: O a. 4.51 m O b. 1.03 m O c. 6.89 m d. 10.52 m

Water is moving at a velocity of 4 m/s in a 1 m wide horizontal channel at a depth of 1 m. The roughness coefficient n=0.025. What is the distance downstream will the depth be increased to 1.1 meters? Select one: O a. 4.51 m O b. 1.03 m O c. 6.89 m d. 10.52 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Situation 5 - A rectangular pile (0.77 x 0.72 m.) is driven in a clayey soil arrangement composed of…

Q: A scuba tank is being designed for an internal pressure of 2,650 psi with a factor of safety of 2.0…

Q: Situation 9 - The angle of internal friction of a cohesive soil which was tested using a tri-axial…

A: Given data, Shearing stress = 250 KPa Normal stress = 480 kPa Angle of internal friction = 26.57°…

Q: What is the value of the bending moment diagram at point D for the beam shown? 120 kN 120 kN 150 kN…

Q: Calculate the Ely value at the midspan using the Moment Area Method

Q: Mr jones is planning a 20-year retirement; he wants to withdraw $6000 at the end of the first year,…

A: Withdraw at the end of the year = $6000 Annual increase in Withdrawal = $800 Time period = 20 years…

Q: 8. Compute for the following and show the tabulated solutions: Azimuth LINES Length (S) AB 1020.87…

A: Solution Line Length Azimuth Latitude departure Correction Adjusted Adjusted Length Adjusted…

Q: If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in…

Q: The optimal number of non-recording rain gauge is The optimal number of recording rain gauge is

A: Data is as shown

Q: The figure shown is the cross section on the fixed support of a propped beam that carries a moment…

Q: 2. The container in the figure is 3.5 ft. wide and is filled with crude oil to a height of 4 ft.…

Q: Draw the influence line for the reaction at A. Find the positive maximum equivalent unit load for…

Q: Course Adj Lat Adj Dep DPD 2A AB -68.99 67.12 BC -58.07 -52.00 CD 69.92 -97.22 DA 57.14 82.10 SUM…

A: Given data:

Q: wen the following technical description, determine if the traverse is closed. If not, balance the…

Q: 20 kN/m 60 kN A E B D - 8 m + tamtam| 8 m El = constant E = 70 GPa 1= 800 (106) mm4

Q: Let Mo = 81kNm. L = 14m Determine the constant C1

Q: A suppressed weir 7.5m long is to discharge 10.125 m3/s of water from an open channel. The weir…

Q: From the given beam loaded has shown; Determine the slope at A in radian. Using Moment Area Method.…

Q: the angle of internal frictional of a cohesive soil which was tested using tria-axial shear…

Q: . Determine the surface tension in a tube with 0.2m radius and wetting angle 80 and capillary rise…

A: Given data in question Radius Wetting angle Cappilary rise Water as capillary fluid To find out…

Q: 9. Find the length of AB and the bearing of line DE for the lot whose other description is given…

Q: Determine the support reactions on the pin and roller as shown in the figure below. Simplify your…

Q: For the cantilever steel beam [E = 190 GPa; I = 82 x 106 mm4), use the double-integration method to…

Q: Situation 3 - A 325 L of carbon tetrachloride weighs 4905 N. What is its unit weight in kN/m3? Round…

A: Given data in question Volume Weight To find out Unit weight

Q: PROBLEM: Determine the instantaneous deflection (dead load only, live load only, and dead + live…

A: Answer We know that the Instantaneous deflection due to uniform load on simply supported beam is…

Q: Answer the following questions: 1) To compute the settlement for a particular soil sublayer, why…

A: Introduction- The Soil consolidation is the mechanical process through which soil progressively…

Q: D A В E wwww ......... .... . 3m 6m 4m

Q: For the loading shown, use the double-integration method to determine (a) the equation of the…

Q: Situation 6 - Kim Jisoo discovered an element (1.43 kN/m3) that flows through a 100 mm (diameter)…

Q: An object (SG = 7.3) floats in mercury (SG = 13.6) such that a certain portion is above the liquid…

Q: A COVID-19 vaccine is administered to residents of a particular city. The syringe has a radius of…

Q: (3L – 4x), Ely wx f elastic curve are the following: Ely = 24 Pa, I = 1660 x 10^6 mm^4 BkN/m, L =…

Q: 21. You have a wellbore that is drilled to 3,298 feet measured depth. Inside it, the customer ran…

A: Option D-378.32

Q: For a circular cantilever beam with loads shown, which location contains the maximum shear stress? T…

A: The answer is found to be Maximum shear stress occurs " at the support,at O" For explanation please…

Q: Given the following Northing and Easting, use the COORDINATE METHOD to solve for the area of this…

Q: From the given beam loaded has shown; Ely = RA®² – M, (æ – 4) + C1, EIy = ¿RA - M, (x – )° +C1æ+ C2…

Q: ituation 4 - Three samples of loose sand were tested under consolidated undrained (CU) conditions.…

A: solution Given undrained angle of friction ϕ=35°for loose sand the cohesive force will be…

Q: Determine the support reactions on the pin and roller as shown in the figure below. Simplify your…

Q: Solid shaft AB rotates at 480 rpm and transmits 30 kW from the motor to gears G and H; 20 kW is…

A: For the given conditions, the minimum possible diameter of the shaft has to be determined

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

Q: Design the slab reinforcement if the maximum positive moment is Mup= wul2/11 and the maximum…

A: L=3mSuperimposed DL=4.76 kPaLL =1.9 kPaSelf weigth=3.45 kPathickness=150 mmAssume,fc'=21 MPafy=345…

Q: From the given figure: Let P = 26KN, L = 8m, a = 3m if the equation of the slope is Ely = Pª (-+L),…

Q: A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure).…

Q: Solve For barred. * and moment of inertia about nentral axis OF t' 5 10 2h 2 10

Q: 12. Situation 4 - A block of wood 0.6 m x 0.6 m x “h” meters in dimension was thrown into the water,…

Q: For the beam and loading shown, us (a) the slope of the beam at C (positi (b) the deflection of the…

Q: A silty sand has a void ratio in loosest condition equal to 0.86 and a void ratio of 0.30 in the…

A: Given data in question Void ratio Relative density To find out In situ void ratio

Q: A high-strength steel bar used in a large crane has a diameter d- 4.00 in. (see figure). The steel…

Q: Using the Moment Distribution Method solve for the support reactions and draw the shear and moment…

A: Moment Distribution Method: This method is presented by prof.hardy Cross. This method is used to…

Q: ITEM 2: w (kN/m) A EI D TIT B 1.5EI EI 7.5m 7.5m 7.5m P= 14 KN, W= 19 kN/m Using Moment Distribution…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

Water is moving at a velocity of 4 m/s in a 1 m wide horizontal channel at a depth of 1 m. The
roughness coefficient n=0.025. What is the distance downstream will the depth be increased to 1.1
meters?
Select one:
O a. 4.51 m
O b. 1.03 m
O c. 6.89 m
d. 10.52 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

.Determine the critical depth in meters for Trapezoidal channel. Base width = 5m Side Slope 2H:3V Discharge = 160 m3/s
1. A 3.1 – m wide rectangular flume carries water at 5.60 m3/s. The bed slope is 0.00078 and n = 0.010. At a certain section, the depth is 92 cm. a. How far therefrom is the depth 80 cm? b. What is the slope of the egl? c. What is the headloss? 2. A rectangular channel 1.8 m wide conveys water at a depth of 1.2 m. a. What is the velocity of flow if it is laid on a slope of 0.002 and n= 0.012? b. What is the discharge if the channel slopes 0.1° and n = 0.016? Use Kutter’s formula for C. c. What is the velocity of flow if S = 0.000263 and f = 0.02?
find the length of the water profile for a wide rectangular that has a bed slopeof 7.5 cm/km and carries a discharge of 2.5 m2/s. The channel terminates intosudden fall., assuming a critical depth at the sudden fall is 0.612 m. Take the Chezycoefficient as 35 (metric)
Determine the critical depth in meters for rectangular channel. Base width = 9m Discharge = 180 m3/s
A rectangular channel carries a discharge of 18.10m3/s when flowing 1.5m depth. If the width of the canal is 10m, determine: The specific energy, Slope of the channel if n= 0.35, and Boundary shearing stress in Pascals.
What is the depth of water in a trapezoidal channel with z = 2.0 and carrying 2.5 cubic meter per second of water flow? The channel’s bottom width is 2.5 m and the velocity of flow is 0.9 m/s.
Determine the critical depth of a rectangular channel having a velocity of 2.215 m/s.
Design a straight trapezoidal erodible channel that can carry a discharge of 12.5m^3/s using tractive force method based on the following information. The side slope is 1V:4H The bottom slope is 0.0015 The manning's roughness coefficient is 0.024 The critical shear stress as 7.2KN/m^2 Angle of repose is 23 Density of water 1000kg/m^3
Water flows at a depth of y1=0.4ft in a concrete channel which is 10ft wide. The discharge per unit width is 10ft2/sec. Estimate the height of the hydraulic jump that will be formed if bed slope is equal to 0.0 and 0.15 respectively.
The side slope of a trapezoidal open channel are 1 horizontal to 1.75 vertical. The bottom width is 2.5m and length of flow is 3m. The coefficient of roughness n=0.015 and the slope of the channel bed is 0.0004. Calculate the velocity of flow (m/s) using Manning's formula. Round answer to one decimal place.
An open channel having a slope of 0.0063 Is to carry 10 m3 /s. The channel material has an n value of 0.036. For a most efficient section of a triangular section Compute the hydraulic mean depth in m. Round your answer to 3 decimal places.
A trapezoidal channel with 3 meters bottom width, side slope 2H:1V, channel gradient of 0.002, and n = 0.025, carries a discharge of 200 m3 /min. Compute the normal depth and velocity. Given data Wbottom (b)= 3 meters Slope= 2:1 S= 0.002 n= 0.025 Q= 200 m3 /min= 3. 33 m3 /sec Normal depth=? Velocity=? Formula below: