Water is pumped from a lake to a storage tank 18 m above at a rate of 70 L/s while consuming 20.4 kW of electric power (Fig. 5- 19). The top of the tank is open to the atmosphere. Disregarding any frictional losses in the pipes and any changes in kinetic energy, determine the pressure difference between the inlet and the exit of the pump. Draw the Schematic Diagram and show your detailed solution. Answer in number only. unit in kPa 18 m Pump

Water is pumped from a lake to a storage tank 18 m above at a rate of 70 L/s while consuming 20.4 kW of electric power (Fig. 5- 19). The top of the tank is open to the atmosphere. Disregarding any frictional losses in the pipes and any changes in kinetic energy, determine the pressure difference between the inlet and the exit of the pump. Draw the Schematic Diagram and show your detailed solution. Answer in number only. unit in kPa 18 m Pump

Name: Kindly solve this problem with complete solution so that I can Underst
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Kindly solve this problem with complete solution so that I can Understand.Correct Final answer: 176.58 kPa 5Water is pumped from a lake to a storage tank 18m above at a rate of 70 L/swhile consuming 20.4 kW of electric power (Fig. 5-19). The top of

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two identical upright cylindrical tanks contains H2O,the first tank is full and the second is 2/3-full. If theradii of the orifices are the same, compare the time todrain of each tank. answer: √1.5
A pipe discharges 142 lps of water into a reservoir at a point 1.85 mbelow the water surface. At point A the diameter is 25.4 cm and the center of thepipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
As given in the figure, the inside of a 125 cm high and 89 cm diameter cylindrical bowl is initially completely filled with oil. Then a 1.25 cm diameter hole is drilled in the bottom edge of the tank and oil starting to discharge from this hole. The oil's exit speed from the tank is given as 2gh. (h is the variable height of the oil in the tank from the hole center and g is the acceleration of gravity). Calculate the time it takes for the oil level in the tank to drop to a height of 15 cm from the bottom as [s].
A spherical tank whose inner diameter is 2 meters is filled with water. If the tank has a hole l cm in diameter at the bottom, when will the tank be half empty given the equation of the rate dV/dt= -0.6S sqrt of (2gh), where: S is the cross sectional area of the hole inside the tank.
As given in the figure, a cylindrical 125 cm high and 89 cm diameter The inside of the tank is initially completely filled with oil. Then, a 1.25cm diameter hole is drilled on the bottom edge of the tank and the oil begins to drain from this hole. Oil outlet speed 2gh given as. (h is the variable height of the oil in the tank from the hole center and g is the acceleration of gravity). From the bottom of the oil level in the tank Calculate the time it takes to fall to a height of 15 cm as [s].
Water flows in a 15-cm-diameter pipe at a velocity of 1.8 m/s. If the head loss along the pipe is estimated to be 19 m, the required pumping power (in kW) to overcome this head loss is ?"
The air velocity in the duct of a heating system is to be measured by a Pitot-static probe inserted into the duct parallel to flow. If the differential height between the water columns connected to the two outlets of the probe is 2.4 cm, determine the flow velocity at the center of the duct in m/s. R of air is 287 J/Kg-K.
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
The cylindrical in the figure is filled with 31.4 m3 of water at t = 0. The radius of the tank is 1 m and its height is 10 m. There is an outlet line with a radius of 0.1 m at the bottom of the tank. a. What is the time required for half of the water in the tank to drain after the outlet line is opened?b. The flow velocity of water from the bottom of a water tank is related to the height of the water in the tank, and this relation is v² = 2gh where v: (m / s) linear flow velocity, g: gravitational acceleration (10 m / s2) and h: (m) height.
In the figure, the cylindrical capacitor, connected to a constant voltage source Vo= 80 V, rests with its edges on the surface of the water of density ρ=1000 kg/m3 . The distance d=0.4 cm between the condenser armatures is much smaller than its radius half. Find the height "h" at which the water level is established between the reinforcements of the condenser. Neglect capillary phenomena. (k=9•109N•m2/C2,κ=81,g=9.8m/2)
Two vertical tanks, one with circular section 3.0 m in diameter, the other square section 1.33 m x 1.33 m are connected by a short tube ( area is 0.725 sq. cm) near bottom. Initially, the head of oil in the first tank is 4.0 m, while in the second tank the head is 60 cm. After a quick opening of the tube's vlave, find the time for the oil surfaces to equalize. Assume the tube properties to be similar to that orifice, with C= 0.78.CHOICES: a.26 seconds b.23 seconds c.21 seconds d.35 seconds
Two vertical tanks, one with circular section 3.0 m in diameter, the other square section 1.33 m x 1.33 m are connected by a short tube ( area is 0.725 sq. cm) near bottom. Initially, the head of oil in the first tank is 4.0 m, while in the second tank the head is 60 cm. After a quick opening of the tube's vlave, find the time for the oil surfaces to equalize. Assume the tube properties to be similar to that orifice, with C= 0.78.