Water is pumped from the river through a 45-mm-diameter hose having a length of 3 m. The friction factor is f = 0.028 for the hose, and the gage vapor pressure for water is -98.7 kPa. Suppose that h= 2 m. (Figure 1) Figure < 1 of 1 > Part A Determine the maximum volumetric discharge from the hose at C so that cavitation will not occur within the hose. Express your answer to three significant figures. IVE ΑΣΦ Q= Submit Provide Feedback ↓vec Request Answer ? liter/s

Water is pumped from the river through a 45-mm-diameter hose having a length of 3 m. The friction factor is f = 0.028 for the hose, and the gage vapor pressure for water is -98.7 kPa. Suppose that h= 2 m. (Figure 1) Figure < 1 of 1 > Part A Determine the maximum volumetric discharge from the hose at C so that cavitation will not occur within the hose. Express your answer to three significant figures. IVE ΑΣΦ Q= Submit Provide Feedback ↓vec Request Answer ? liter/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water at 15°C (? = 999.1 kg/m3 and ? = 1.138 × 10−3 kg/m·s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
Two water reservoirs of height h1 = 60 m and h2 = 30 m are connected by a pipe that is 0.35 m in diameter. The exit of the pipe is submerged at a distance of 8 m from the (2nd) reservoir surface. a. Provide a diagram b. Determine the flow rate through the pipe if the pipe is 80 m long and the (Fanning) friction factor f' = 0.004. The pipe inlet is set flush with the wall. c. If the relative roughness ε/D = 0.004, determine the friction factor and flow rate.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. a) Determine the head loss in the “smooth” pipe in meters if the friction factor is 0.014. b) What gage pressure p1 in kPa, is needed to provide the given flow rate?
With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized chamber A is poured into the atmosphere with a 40 cm fixed diameter BCDEF pipe. Since zB=29, zC=10, zD=28.5, zE=5 and zF=28 meters according to the comparison plane;a) Calculate the flow of the system.b) Draw the relative load (energy) and piezometer lines of the system.c) Determine where the greatest pressure will be observed throughout the system and calculate its relative value.
A water main line is composed of two pipes connected in series, pipes AB and BC. Pipe AB is 500 m long and 30 cm in diameter while pipe BC is 800 m long and 20 cm in diameter. Point C is 10 m higher than point A. The pressure at point C is 3 kg per square cm higher than the pressure at point A and the coefficient for minor head losses due to contraction and enlargement are 0.40 and 0.25 respectively. Determine the discharge and flow direction on the water main line using Darcy-Weisbach formula with f = 0.02 for all pipes. Draw approximately the EGL and HGL.
In a pipe 300 mm in diameter, water flows over a length of 300 m, connecting point A, at topographic elevation of 100.0 m, in which the internal pressure is 291 kPa, to point B, at topographic elevation 74 .0 m, where the internal pressure is 334 kPa. Determine the direction of flow. Data: Specific gravity of water = 10 kN/m3. A) from B to A B) There is no drain. 0 C). from A to B For the previous question, calculate the pressure drop between A and B, in meters. ( ) If the flow is equal to 0.18 m3/s, calculate the friction factor of the pipe. ( ) For this same flow rate, calculate the friction velocity. ( )
For this system, the discharge of water is 0.15 m3 /s, x = 1.0 m, y = 2.0 m, z = 8.0 m, and the pipe diameter is 30 cm. Neglecting head losses, what is the pressure head at point 2 if the jet from the nozzle is 10 cm in diameter? Assume α = 1.0 at all locations.
6. Compute the lost head in a 150-mm pipe if it is necessary to maintain a pressure of 231 kPa at a point upstream and 1.83 m below where the pipe discharges water into the atmosphere at the rate of 0.0556 m /s. indicate free body diagram
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized aire in the tank. a.) Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. b.) What gage pressure in p1 in kPa, is needed to provide the given flow rate?
Estimate the equivalent hydraulic conductivity for flow in the horizontal direction. Also calculate the ratio of kv(eq)/kH(eq). Suppose that k1 = 15 x10^-4 cm/s, k2= 5.0x10^-4 cm/s, k3= 3.0 x10^-4 cm/s, k4= 2.0 x10^-4 cm/s, H1= 1.0 m, H2 = 2.0 m, H3 =1.5 m, H4 =1.0m. kH(eq) = kV(eq)/kH(eq)=
Two reservoirs are connected by three pipes. laid in parallel. The pipes diameters are respectively 10cm, 20cm and 30cm and they are of the some length. If discharge through 10cm pipe is 0.1 m3/s, calculate the discharge through the larger pipes. Assume the friction coefficient ‘f’ to be same for the pipes.
1. A pipe has a slope of 1 in 100 and its length is 300 meters. Its diameter is 0.6 meter at the lower end while 1.2 meters at the higher end. The rate of flow through pipe is 5400 liters/min. Find the pressure at the lower end if the pressure at higher end is 68.07 kPa. Neglect losses.