1. As a junior city engineer of a municipality, you are tasked todesign the specifications of the pump with 3650 cu.m/day. Thewater source in the municipality is from an open reservoir andwill supply to a pressure tank that will distribute to themunicipality.open4l PressurereservoirTank70 m15 mPumpDetermine the following specifications of the pump and pipingsystem (assume fluid stagnation at the pump).Velocity head at pt.1 to 2 if the diameter of the pipe isa.)200 mmb.)Suction pressure of the pump in kPa (Pressure at pt. 2).c.)Velocíty head at pt.3 to 4 if the diameter of the pipe is150 mmd.)Discharge pressure of the pump in kPa (Pressure at pt. 4).Assume atmospheric pressure at the pump.If an air vent is installed at the pipe just right beforethe pressure tank with diameter of 20 mm, what is thevelocity of discharge in m/s?The height of the pressure tank is 12 m, what is theflowrate in cu.m/hr at pt.5 if the diameter of the pipe is150 mm?e.)f.)

Since the question asked by you contains more than three sub-parts, so according to our guidelines,…

water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open reservoir O Pressure Tank 70m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is 200 mm a.) b.) Suction pressure of the pump in kPa (Pressure at pt. 2). Velocity head at pt.3 to 4 if the diameter of the pipe is 150 mm c.)

water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open reservoir O Pressure Tank 70m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is 200 mm a.) b.) Suction pressure of the pump in kPa (Pressure at pt. 2). Velocity head at pt.3 to 4 if the diameter of the pipe is 150 mm c.)

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

What will result from too little EGR flow? And what can cause a reduction in the flow?
Which of the ff are assumptions followed by the Bernoulli eq ? the pump is working at 100% efficiency , skin friction is negligible, the flow of the fluid is strictly turbulent, the velocity head is negligible
The power output is 30 Hp to a centrifugal pump that is discharging 900 gpm and which operates at 1800 rpm against a head H=120 ft, 220 V, 3 phase, 60 Hertz. If this pump is modified to operate 1200 rpm, assuming its efficiency remains constant, determine its discharge in gpm, the theoretical head if imparts to the liquid, and the power input to the pump
1. A centrifugal pump delivers 900 ?3/ℎ? of sea water (sp.gr.= 1.03) from a source wherethe water level varies 2 m from high to low tide level. The pump centerline is located2.6 m above the surface of the water at high tide. The pump discharges into theatmospheric surface condenser, 3 m above the pump centerline. Loss of head due tofriction in the suction pipe is 0.8 m and that in the discharge side is 3 m. Pump is directlycoupled to a 1750 rpm, 460 volts, 3 phase, 60 Hz. Calculate: a) total dynamic headb) pump theoretical powerc) power to drive the pump if pump efficiency is 82%
What are the frictional losses to be considered when calculating power consumption of a pump under operation?
If a pump requires a minimum of 2.75 m of NPSHA, how high can the centerline of the pump be located above the top of an open tank that supplies 27 C water to the pump? The barometer reads an average of 732 mmHg throughout the year. The tank is 1.82 m high. The pipe friction is 0.7 m and the velocity is 1.22 ?/? .
A centrifugal pump operating under steady flow conditions delivers (2000 + K) kg/min of water from aninitial pressure of [100 + (K/2)] kPa to a final pressure of [1000 + 2K] Pa. The diameter of the inlet pipe tothe pump is 20 cm and the diameter of the discharge pipe is 8 cm. What is the work done? IMPORTANT NOTE: K=821
You are asked to calculate a rotadynamic pump with a total manometric head of 11 mss and demand flow of 19 in lt / s, which will meet the daily water need of a facility, and which can rotate at 1450 rpm for its drive, using a three-phase electric motor. Since the density of the water to be transported is 1000 kg / m3; a) Calculate the pump organs.
A centrifugal pump driven by a 160-hp motor rotating at 2400 rpm is used to pump 70°F water in a manufacturing plant. The pump operates against a head of 100 ft and has an efficiency of 70%. If this pump is used under a head of 196 ft, what power will be required?
A double suction centrifugal pumps delivers 25ft3 of water at a head of 12m and running at 650rpm. What is the specific speed of the pump? ANSWER: 3097.77rpm
For pumping a liquid refrigerant with a density of 1226 kg / m3 D1 = 200 mm, D2 = 360 mm, b1 = 50 mm, b2 = 30 mm in a designed centrifugal pump. It When the pump operates at n = 1720 rpm, H = 0.25 at a manometric head of 14.5 m It will pump this fluid at a flow rate of m3 / h. Taking Alfa 1 = 90 °, Yield = 85% and Yield h = 91%, and find the angles 1 and β2.
A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60% requires 4.1 kW at 1000 rpm. What is the theoretical discharge if the speed is increased to 1500 rpm assuming the efficiency remains constant? What is the theoretical head and kW at 1500 rpm?.