We explained that the electric power consumption of various electricalcomponents can be determined using the following power formula: P = VI = RI2 where P is power in watts, V is the voltage, I is the current in amps, and R is the resistance of the component in ohms.Plot the power consumption of an electrical component with a resistance of 145 ohms. Vary the value of the current from zero to 4 amps. Discuss and plot the change in power consumption as the function of current drawn through the component.

We explained that the electric power consumption of various electricalcomponents can be determined using the following power formula: P = VI = RI2 where P is power in watts, V is the voltage, I is the current in amps, and R is the resistance of the component in ohms.Plot the power consumption of an electrical component with a resistance of 145 ohms. Vary the value of the current from zero to 4 amps. Discuss and plot the change in power consumption as the function of current drawn through the component.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter18: Mathematics In Engineering

Section: Chapter Questions

Problem 4P: In Chapter 12, we explained that the electric power consumption of various electrical components can...

See similar textbooks

Similar questions

5.) The figure shows a metal hanging by a thin wire from a floating wood block. The wood block has a specific gravity Sb =0.25, a square base of 80 mm x 80 mm and height of 15 mm. The metal has a volume of 8000 mm^3. Using a unit weight of water 9800 N/m^3 and g=9.80 m/s^2., find the mass of metal in grams. Write your answer in two decimal places. fluid mechanics
Based on unit considerations alone, show that the power needed to accelerate a car of mass m (in kg) from rest to velocity V (in m/s) in time interval t (in s) is proportional to mass and the square of the velocity of the car and inversely proportional to the time interval.
7. solve for the density (kg/li) of a certain liquid if it has a relative density of 0.95. 8. compute for the specific weight (N/m^3) of a spherical ball if the diameter is 21 cm and has a mass of 10 kg
The total weight of the object shown in the figure is W.Calculate the moment of inertia about point A. About x axis (L1 = 16; L2 = 10;W = 44N)
The figure represents three-quarters of a disk rotating around an axis that passes perpendicular to its diameter. The part has mass M, radius R, and surface density that varies with radius σ= 2Mx-2. Find the moment of inertia of the part.
6.) The figure shows a metal hanging by a thin wire from a floating wood block. The wood block has a specific gravity Sb =0.25, a square base of 80 mm x 80 mm and height of 15 mm. The metal has a volume of 8000 mm^3. Using a unit weight of water 9800 kN/m^3 and g=9.80 m/s^2, find the tension in the thin wire in Newton. Write your answer in three decimal places. fluid mechanics
In the given figure, calculate the value of h if the moment of inertia of the plane region under the u-axis is 120x10^9 mm^4 and I, is equal to 14x10^3 mm, The area is given by 90x10^3 mm^4, Answer in a whole number.
Calculate the mass (in kilograms) of a sphere of gold of radius 10.0 cm; the density of gold= 19.3 g/cm 3
A cylindrical tank is having a hemispherical base. The height of the cylindrical portion is 4 m and the diameter is 3 m. At the bottom of this tank, an orifice of a diameter of 300 mm is fitted. Find the time required to completely empty the tank. Take Cd= 0.60. Include a diagram in your solution. a.217 seconds b.127 seconds c.145 seconds d.175 seconds
a manometer is a device that measures pressure. a common simple manometer consists of a U shaped tube of glass filled with some liquid. 1. the height of kerosene in the left leg was measured as 8.3 cm high and 5.2 cm on the right leg. yhe difference in elevation between the interfaces of kerosene and water measured 2.5cm. determine the specific gravity of kerosene.
Determine the mass moment of inertia of a steel shaft that is 130 cm long and has a diameter of 6.4 cm . Express your answer in kg · m2 .
Determine the mass moment inertia of a steel shaft that is 2 m long and has a diameter ( d ) of 10 cm. The density of steel is 7860 kg⁄m3 .