We have a device that contains two shafts and a motor with a power of 15kW and a speed of 1500rpm is connected to one of its shafts in the form of a coupling. We know that the second shaft is connected to the first shaft by two gears and receives part of the power, also a gear, a pulley and a sprocket are responsible for removing power from these two shafts. 40% of the power in the gear, 4% of the pulley belt and the rest is divided by zero and maximum by the chain wheel in an oscillating manner. Design these two shafts in an almost optimal position Hints : 1_ Select the type and location of power consumable parts according to your decision 2_Selection of items such as shaft material, safety factor, etc., stating logical 1/2

We have a device that contains two shafts and a motor with a power of 15kW and a speed of 1500rpm is connected to one of its shafts in the form of a coupling. We know that the second shaft is connected to the first shaft by two gears and receives part of the power, also a gear, a pulley and a sprocket are responsible for removing power from these two shafts. 40% of the power in the gear, 4% of the pulley belt and the rest is divided by zero and maximum by the chain wheel in an oscillating manner. Design these two shafts in an almost optimal position Hints : 1_ Select the type and location of power consumable parts according to your decision 2_Selection of items such as shaft material, safety factor, etc., stating logical 1/2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A power of 6 kW is supplied to the motor of a crane. The motor has an efficiency of 90%. With what constant speed does the crane lift an 800 lb weight. The correct answer is 1.5 m/s.
In a belt–pulley wheel system, the effective tension in the belt is 500 N and the diameter of the driver wheel is 200 mm. If the power output from the driving motor is 5 kW, the driver pulley wheel turns at: 50 rad/s 2500 rad/s 100 rad/s 0.1 rad/s
(i) Find the thickness of an isolated block in ‘meter’ capable of being charged to 2.4 x 106Volt potential before sparking into the air, given that dielectric strength of air is 24,000V/cm. (ii) Find the heat energy(flow) in ‘Joules’ required to prepare a coffee in an electric kettlewith 0.5 litre (1litre = 10-3 m3) of water which is heated from 30ºC to 85ºC?Take density of water as 1000 kg /m3and Specific heat of water as 4.187 kJ/kg º K.
An inventor claims to have a solar powered heat pump that receives energy as heat from the sun at the rate of 10 kW and extracts energy as heat from the environment at the rate of 7 kW. This system does not require any shaft or electrical power input. If you think this device is impossible, explain why using basic principles to support your argument. If you think it might be possible, what would be the steady-state rate of transfer of energy as heat to the house? (Assume TH = 20 Cand TL = -15 C).
A cylinder with an area ratio of 0.2 and a bore diameter of 8.0 cm steadily extends a 13.3 kN load. If the cap-side pressure is 4 MPa and the rod-side pressure is 250 kPa, what is the force efficiency of the actuator? Also, what is actuator efficiency in %?
An electric motor drives a gearbox of a conveyor belt via a fluid coupling. The motor delivers 40 kW at a speed of 1550 r/min. Take the efficiency of the coupling as 96% and calculate: a. the torque on the gearbox shaft, b. the speed of the gearbox shaft, c. the heat developed in the couplin
(11) A 120cm diameter diamond circular blade, mounted on a pulley-driven steel shaft, is requiring a blade peripheral linear speed of 45m/s. Motor drive is 100kW @ 1,200rpm with 150mm drive pulley. Determine: (a) the shaft rpm to attain blade peripheral speed required; (b) the shaft diameter; (c) the shaft pulley diameter.
A pulley wit a diameter of 40cm is driven by a belt with thickness of 1,2mm. The tension in the tight side is 320,324N and the tension in the slack side is 123,154N.the belt velocity is 12mls. calculate the rotational frequency of the pulley and the power trasmitted by the belt in kW?
An open belt running over two pulleys 24 em and 60 cm diameters connects two parallel shafts 3 m apart and transmits 3.75 KW from the smaller pulley that rotates at 300 r.p.m. coefficient of friction between the belt and the pulleys is 0.3 and the safe working tension is 100 N/em width. Determine: i) minimum width of the belt, ii) initial belt tension, and i) length of the belt required.
1) An electric motor’s torque is a function of the speed at which it rotates. Many brushed AC motors have a linear toque curve as shown below. If the power output of the motor is equal to the torque (T) multiplied by the rotational speed in rad/s (w), what is the maximum power you can get out of the motor if the stall torque (Tstall) is 0.001 Nm and the no load speed (wno load) of 10,500 RPM? Give answer in Watts.
A belt wrapped around a pulley 600 mm in diameter has a tension of 800 N on the tight side and a tension of 180 N on the slack side. What power in kW is being transmitted if the pulley is rotating 200 rpm? The correct answer is 3.89 kW
1. The mean effective pressure of an engine running at 300 rpm is 500 kPa. What is the indicatedpower if the engine has bore of 250 mm x 450 mm. Select the correct answer below: A. 110.5 kW B. 150 kW C. 200 kW D. 182. 2 kW 2. In a certain process, entering is 1500 KJ/kg and 150 m/s. If the energy leaving is 12000 Kj/kg/ Determine the velocity at exit. Select the correct answer below: A.) 145 m/s B. 1020 m/s C. 789 m/s D. 978 m/s