What are the diagnostic criteria in Cyclic Voltammetry for an irreversible process

Q: Explain the Thomson effect, and the figure of merit for thermoelectric materials

A: When an electric current runs through a circuit comprised of a single material with a…

Q: Calculate the thermoelectric sensitivity of (a) a platinum-constantan, (b) a platinum-nickel…

A: Thermoelectric sensitivity In reaction to a temperature differential over the whole material, the…

Q: is often used for welding materials that can accept only a low heat input, e.g. certain stainless…

A: Laser beam welding is often used for welding materials that can accept only a low heat input.  Laser…

Q: e specific heat at co

A: Specific heat ( Cp) =136.15 lb/lb °R

Q: If the the probability of Alpha particles with energy 5 MeV  to be scattered through an angle theta…

A: Scattering of alpha-particle is introduced and explained by Rutherford. single scattering of alpha…

Q: What measurements are carried out to find the experimental value of the thermoelectric work…

A: Any of a group of solid-state devices that convert heat directly into electricity or convert…

Q: IDENTIFY THE NUMBER OF ATOMS (CL, C, H, and F) in the Refrigerant R111

A: Givenrefrigerent R111

Q: Gas diffusion layers are typically placed between: O The anode catalyst layer and the membrane. O…

A: fuel cell can be considered as device which produces electricity. The process involved is called…

Q: ROBLEM: IVD-39 BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD

A: ns are always required to be used only when the convective heat transfer coefficient h are…

Q: What is inelastic collision?

A:

Q: Transient Cooling What is lumped capacitance? What does the biot number rpesent, and why must it be…

A: Lumped Capacitance :- Lumped capacitance is in general, the temperature of a body varies with…

Q: Normal (P = 1 atm) boiling point: 280K Normal melting point: 190 K Triple point: 170 K, 0.800 atm

A: c. At 0.8 atm and 250K, the substance is a solid

Q: IDENTIFY THE NUMBER OF ATOMS (CL, C, H, and F) in the Refrigerant R113

A: It is required to determine number of atoms in R113 refrigerant

Q: Which of the following is NOT TRUE about the diffusion coefficient equation?   A. Its value…

A:

Q: AH of vaporization of water is 439.2 cal/g at the normal boing point. Since virus can survive at…

A:

Q: The rating of the ability of a gasoline to burn smoothly in an internal combustion is its     a.…

A: The rating of the ability of a gasoline to burn smoothly in an internal combustion is its octane…

Q: A substance has a melting point of 20°C and a boiling point is 150°C. The latent heat of fusion of…

A: According to the conservation of energy, The heat gain by the ice should be equal to the heat loose…

Q: A properly working solar dish must have value of concentration ratio О а. None of these O b. less…

A: Concentration ratio is more then 1

Q: What is the explanation on this diagram?

A:

Q: Cobalt-60 is commonly used as a source of beta-particles. How long does it take for 87.5% of a…

A:

Q: If one's hands are being warmed by holding them to one side of a flame, the predominant form of heat…

A: Vaporization is the process of converting the liquid substance to vapour. It can be the boiling or…

Q: What is FRL Unit?

A: The abbreviation FRL stands, F for the filter, R for the regulator, and L for the lubricator. Thus…

Q: A reverberation chamber has dimensions such that its volume-to-surface area ratio, in S.l units, is…

A: Given:  let V and A be the volume and area of the reverberation chamber volume-to-surface area…

Q: What is null and alternative hypotheses.

A:

Q: Find the magnitte omot difection-of theresultant focees? 15 usiny Purtatlogrnm tang

A:

Q: Why should we avoid wet contact with electrical appliances? Provide a mathematical justification for…

A: When there is a wet contact with electrical appliances, Equivalent resistance reduces. This is…

Q: Explain what the following terms mean: (i) Isobaric. (ii) Adiabatic.

A: Isobaric and adiabatic are thermodynamic processes.

Q: can you sketch a schematic diagram, labelled withtemperature values, magnitude and direction of…

A:

Q: Explain internal energy in relation with enthalpy. Provide suitable mathematical equations to…

A: Internal energy of a thermodynamic system is the energy that the molecules inside the system…

Q: A jet of water flows from a 12.5 cm2 crater with a constant charge of 1.125 m where the minimum…

A: Volume of water coming out of pipe per sec is given by=A×v=20×10-4×10=0.02m/s

Q: Which is the more stable positon ?

A: It is asked to find the more stable position

Q: diagnostic criteria in Cyclic Voltammetry for an irreversible process

A:

Q: What is the basic difference between adsorption and absorption?

A: Adsorption is the adhesion of atoms, ions or molecules from a gas, liquid or dissolved solid to a…

Q: Make up a multiple-choice question about evaporation and condensation energy changes.

A: Which of the following options are correct? Statement 1: Evaporation happens when a liquid is heated…

Q: (c) A hardboard wall is exposed to a window on a neighbouring property which is 2 metres high x 2…

A: Laminar flow :Fluid flow in which the adjacent layer of the fluid do not mix with each other and…

Q: Consider the osmotic pressure-mediated nuclear compression under various concentrations of…

A: Given : V = 1500 μm3 Vf = 1000 μm3 10% PEG solution To find : Bulk modulus

Q: A substance has a melting point of 20°C and a heat of fusion of 2.4 × 10 to power of ((4)) J/kg. The…

A:

Q: What are the diagnostic criteria in Cyclic Voltammetry for a reversible process and irreversible…

A: Voltage (applied to an electrolytic cell consisting of two or three electrodes immersed in a…

Q: Difference between metallurgical efficiency and economic efficiency in relation to mineral processin

A:

Q: Why the fire is considered a serious industrial hazard?

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Basic Thermodynamic Processes

The word 'thermodynamics' can be divided into two words, 'thermo' and 'dynamics'. The word thermo deals with the heat and thermal phenomenon, whereas dynamics deals with forces or external agent that drives the heat flow or aids in the motion of heat.