what does the IPCONFIG command do

Q: Task no 1. Explore the syntax “ipconfig” and “winipcfg”. Note down your observations?Ipconfig is a…

A: We have the difference between ipconfig and winipcfg commands. We need to tell why we use these…

Q: From a user's perspective, what is the difference between the download-and-delete mode and the…

A: The answer of the question is given below:

Q: Which table is created in switches using MAC address? O a. history table O b. MAC address table O c.…

A: A switch builds its MAC address table by recording the MAC address of each device connected to each…

Q: The netstat command (available on Linux and Windows) displays a computer's active network…

A: Netstat is a command which is used in LINUX or WINDOWS to display the number of incoming and…

Q: Which command tests for connectivity between two computers?

A: To be determine: Which command tests for connectivity between two computers

Q: 1. From the command prompt in Windows, run the command below: netstat -r Use the output from this…

A: The host address for my host is 192.168.1.0 It's network prefix is 24, as when we convert…

Q: Which command will display the number of hops between your computer and the other?

A: HOP counts refer to the number of devices, usually routers, that a piece of data travels through.

Q: How will you find out the DNS server information? Write the command and attach the screenshot.

A: To find out the DNS used by your PC follow the below steps: Go to start Type cmd Open command…

Q: Which of the following commands can be used to find the hostname of your computer on Windows?…

A: Host Name will appear at the top, under the section Windows IP Configuration.…

Q: Which command allow you to request an IP address as a DHCP client?  (Choose all that apply.) a) dh…

A: Incorrect options: a) dh dh is a Linux command that helps in executing a set of debhelper commands…

Q: What do these troubleshooting commands do? ping, traceroute/tracert, nslookup, ipconfig/ifconfig,…

A: Ping  means the time it takes for a small data set to be transmitted from your device to a server on…

Q: What is the sudo command?

A: sudo is a Unix command. Using the sudo command you can run Unix command as another user.  Sudo…

Q: Watch the NSLOOKUP video in this week's module, and as you watch the video, answer the following…

A: 1)IPv4 address of 'a' root server = 198.41.0.4

Q: Which setting controls access to shared files when users are disconnected from a network? Select…

A: Here the given options are caching, permission level, permissions and shared nodes snap-in . All…

Q: 185.75.255.10

A: IP addresses are utilised for finding the wide range of various PCs present on an organization. IP…

Q: To add the IP address 204.168.8.100 with the MAC address 00-14-22-01-23- 45, what command will you…

A: The solution to the given problem is below.

Q: Which Cisco command will provide information about the status of all interfaces including the number…

A: Show Interfaces, this is the command used.

Q: The IPv6 has O options O header checksum O fragmentation O anycast address feature, which is not in…

A: The Answer is

Q: What is the list loopback command for IPv4? What is the IPv6 command list?

A: Intro List loopback command for IPv4 ? The loopback network in IPv4 is 127.0. 0.0 with a subnet…

Q: What parameter can be added to the netstat command so that you can see what programs are using a…

A: To be determine: What parameter can be added to the netstat command so that you can see what…

Q: Use the command that shows the IP address of your device. (Non-anonymous question O) * (1 Point) 1…

A: Given 8)To know the command that show ip address of device. 9) subnet mask 255.0.0.0.

Q: 2 B- 5 <?php // Variable to check = "2001:0db8:85a3:08d3:1319:8a2e:0370:7334"; Sip e // Validate…

A: It is defined as Hypertext Preprocessor (PHP) is a programming language that allows web developers…

Q: List loopback command for IPv4 ? List command for IPv6?

A: List loopback command for IPv4 ? The loopback network in IPv4 is 127.0. 0.0 with a subnet mask of…

Q: If you are connected to a network that uses DHCP, and you need to terminate your Windows…

A: The command used for terminating the workstation of Dynamic Host Configuration Protocol (DHCP) is…

Q: Write a short note on IP addresses?

A: Actually, IP stands for Internet Protocol

Q: ust get IP address automatically from the DHCP server. Make sure your server does not impact to…

A: Q. Employee workstation must get IP address automatically from the DHCP server. Make sure your…

Q: dnsrecon -d cuny.edu returns few IP addresses. Is 128.228.1.10 a Start of Authority address? a. True…

A: An IP address recognizes a computing device among millions of devices connected via a large network.…

Q: Q12. The file /etc/resolv.conf configures access to a DNS server. True/false. Q13. Cardctl is…

A: these questions are based on commands and dns server in computer science.

Q: QUESTION 24 Which command is used to show details about the path that a packet takes from the…

A: Ans.24  a. Ipconfig Shows generally current TCP/IP network setup esteems and invigorates Dynamic…

Q: If you were to see the following command run, what would you assume? hping -S-p 25 10.5.16.2 Someone…

A: Answer: hping is a program used to send uniquely planned messages to a target. You use command-line…

Q: Issue a command to identify which ntp server (list it in the response) your client is connected to,…

A: Open Command Prompt/ Windows Powershell ( Run as administrator).

Q: What are the misconfiguration of the following screenshot of the DHCP that controls WLAN are (Choose…

A: Correct option: D

Q: What is the Apache web server, exactly? Examine the configuration file /etc/httpd/conf/httpd.conf…

A: Introduction Actually, the Apache web server is the most widely used webserver software on the…

Q: Router: your first name switch: last name user: first name with encrpted pass class12345 secure all…

A: There are two switches on a router.  1st IP Address = 192.168.4.0/28 (PC1 and PC2) and available PC…

Q: Create Static Route from PC0 to PC5

A: Router 0 Router&gt;enRouter#configure terminalRouter(config)#ipv6…

Q: 8- Which of the following is NOT a valid field found in IPV4 header? * Protocol O Destination IP…

A: Given:   We have to answer which of the NOT a valid field found in IPv4 header .

Q: IPSec SA and the IKE SA is the same thing.True or False.

A: To be determine: True or False

Q: Explain how the ICMP ping messages are able to travel across different networks. (Write the answer…

A: Need to explain : How the ICMP ping messages are able to travel across different networks. Need to…

Q: What command can be used on a Windows PC to see the IP configuration of that computer? show…

A: Solution In order to get IP configuration of a system we will use  ' ipconfig ', A proper…

Q: Drop Send Turn off Unknown Syslog Port Frames Protect Restrict Shutdown

A: Dear Student, Since The required diagram for SW2 is not available so, I am answering the question In…

Q: DHCP clients send a DHCPREQUEST packet when they require a new IP configuration.True or False?

A: DHCP  Dynamic Host Configuration Protocol is a network management protocol. It is used on Internet…

Q: which command displays your default gateway?

A: ifconfig  displays the default gateway. The ifconfig command is used for displaying current network…

Q: What is the MAC address associating with your default gateway? Please provide a snapshot to show how…

A: It is defined as Media Access Control which is the physical address, which uniquely identifies each…

Device network connection

The network segment is formed by attaching connectivity devices to network cables. Data are not filtered by the hub. The data packets are transmitted again to all the parts through the hub. Nowadays the computers are connected to networks using a hub or switch.