What happens when the anode-to- cathode voltage exceeds the * ?forward-breakover voltage The device turns on and conducts when VAK exceeds the forward- breakover voltage and will be damage. The device turns ON and not conducts when VAK exceeds the forward-breakover voltage. The device turns on and conducts when VAK exceeds the forward- breakover voltage. The device turns OFF and conducts when VAK exceeds the forward- breakover voltage.

What happens when the anode-to- cathode voltage exceeds the * ?forward-breakover voltage The device turns on and conducts when VAK exceeds the forward- breakover voltage and will be damage. The device turns ON and not conducts when VAK exceeds the forward-breakover voltage. The device turns on and conducts when VAK exceeds the forward- breakover voltage. The device turns OFF and conducts when VAK exceeds the forward- breakover voltage.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
What is the difference between a diode and rectifier?
For the following circuit; a)- Diodes' conduction-cut status ("On" or "Off") determine mathematically.? (For diodes voltage drop model will be used. For each diode Vd = 0.7 V). b)- Currents passing through all branches of the circuit calculate? c)- 10 kΩ resistor on the right of the circuit Calculate the power spent on it.
. Give the short answer offollowing questions each question carries equal marks Don’t need tobriefly explain Its better to give point to point answer . (a) How zenerdiode is a special diode (b) Explain the difference between zener and avalanche effect (c) Explain break down voltage (d) Draw the symbol of PN junction diode, tunnel diode , Zener Diode. (e) How collector size is more than emitter (f) How NPN transistor is more good as compare to pnp (g) Why collector have more size than emitter
TRUE OR FALSE- When different diode models are connected in series in such a way that they are oriented similarly i.e. will allow a specific current flow, the voltage required to forward bias the series connection is the forward voltage of the diode with the higher knee voltage specification. - When different diode models are connected in parallel in such a way that they are oriented similarly i.e. will allow a specific current flow, the voltage required to forward bias the parallel connection is lower than the forward voltage of either of the diodes knee voltage specification since they are connected in parallel i.e. their equivalent resistance is lower as well.
Draw band diagrams for below contacts. a) metal-n-type semiconductor for Φm< Φs b) metal-n-type semiconductor for Φm> Φs c) metal-p-type semiconductor for Φm< Φs d) metal-p-type semiconductor for Φm> Φs Clearly specify type of contact, Schottky barrier, built-in-potential and the depletion width in the band diagram
The carrier concentrations (Figure 1) are approximations for the case where the net (n-type or p-type) doping of the semiconductor is very well defined (>> ni ). For generic semiconductor doping, the relations in Figure 2 take effect. Deduce the relations from Figure 2. Please explain each step as I'm having trouble in understanding this subject. P.S.: I sent this question before and the signals in Nd and Na came out wrong. Please be aware!
ANSWER ALL WILL UPVOTE IF CORRECT 7. What is the maximum conduction angle for an SCR? a. 90, b. variable, c. 180, d.360 8. A breakover type of device can be represented as a long resistor with a diode tapped somewhere in the middle. a. SCR, b. BJT, c. FET, d. UJT 9. It is the ratio of the resistance at the base1 terminal to the resistance across the two bases. a. base resistance ratio, b. interbase resistance ratio, c. intrinsic standoff ratio, d. intrinsic resistance ratio 10. the duration (in degrees) of an AC cycle that the SCR is turned on a. turn on angle, b. firing angle, c. conduction angle, d. firing delay angle
With the help of a well labelled diagram briefly explain the operation, characteristics, andapplications of the following semiconductor diodes.a) Zener diodeb) Light Emitting Diode (LED)