What is attitude indicator

Q: Cleaning a machine with compressed air is a general safety precautions considered while working in a…

A:

Q: Answer should be detailed:   High Speed Airspeed  Instruments  Low Speed Airspeed Instruments

A: 1. High-speed airspeed instruments consist of airspeed indicators in airplanes, helicopters,…

Q: Choose correct answer: The hydraulic system is _____________________________________ none of the…

A: Hydraulic systems use fluids as a medium in exerting loads where as in pneumatics, compressed air is…

Q: The distance depends on the observer’s relative motion. Explain the statement.

A: Given Data⇒relative motionProblem definition⇒Problem says The distance depends on the observer’s…

Q: ..... ..... will extend the life of the equipment

A: ................. Will extend the life of the equipment.

Q: What is a solution to the following environmental risks in a SADA system Temperature Corrosion…

A: SADA system stands for Solar Array Drive Assemblies. These are the system in which the solar array…

Q: hich of the following is not a component of a pneumatic system? Group of answer choices An electric…

A: the electric motor is used in the pneumatic system, it converts compressed air energy into…

Q: Unusual smell during machine operation is cause to problem. Select one: True False

A:

Q: Which one of the following mechanisms is used to control the rotor speed of the wind turbine?…

A: Objective: To determine the mechanism used to control the rotor speed of the wind turbine.

Q: What is UAV

A: A UAV(Unmanned Aerial Vehicle ) ,also popularly known as "Drone", is an aircraft or airborne system…

Q: Discuss the steps on how to perform a proper hazard control. Give some examples

A: Hazard Control : Hazard control consists of all necessary steps and practices to protect workers…

Q: Risk Assessment: State the impact it can have on the Rover and other (if applicable) and how…

A: A risk assessment is a method of identifying prospective dangers and determining what could…

Q: From the following identify  the false statement . In general safety precaution the machine should…

A: Precaution and safety

Q: The first purpose of vehicle maintenance is * The vehicle in good running condition The operation…

A: Maintenance: It is a process which is done to maintain the proper condition and run with accurate…

Q: Water pump at home is not working properly. Do fault tree analysis

A: Pump: Pump is a device that is used to increase the pressure of the fluid. In various applications,…

Q: From the following identify the false statement . A) In electrical safety precaution, necessary…

A: A)In electrical safety precaution- The precautions that should take to avoid the overloading of…

Q: if the ultrasound sensors are positioned as shown below which of the following statements is…

A: Doppler Ultrasound :  The main function of Doppler Ultrasound is to utilize in the clinical…

Q: 3- In the event of a malfunction in the engine temperature sensor, how will it affect the operation…

A: Given :-  In the event of a malfunction in the engine temperature sensor, how will it affect the…

Q: Which of the following is the best example of engineering control? A. noise-cancelling headphones

A:

Q: Question: What is the main difference between active Sensor and passive Sensor: ( Select the…

A: A sensor transducer is a device which converts a physical form of signal into measurable form of…

Q: what are the five non-destructive techniques normally used for predictive maintenance.

A: The non-destructive techniques (NTD) used for predictive maintenance are discussed below: (1) Visual…

Q: How to connect the sterilizer in the drone to the aircraft's control panel

A: A drone controller works by sending a radio signal from the remote control to the drone, which…

Q: Which of the following is not used in automation of warehouse operations: Select one: Forklifts…

A: Although all the given options can be used in warehouse operations but if we had to select one which…

Q: the following is not true regarding optical comparator? All of them are true b. High magnification…

A: Comparators are used to determine the difference in dimensions between a given component and a…

Q: If the first digit of the diagnostic trouble codes is a zero (0) what does it mean

A: When a vehicle’s on-board diagnostics system detects a malfunction, it generates the appropriate…

Q: The following instruments are considered gyroscopic. * Tachometer VSI Altimeter Fuel…

A:

Q: recognize where energy can be saved. hese energy savings can be maintain air systems or application…

A: Given

Q: Housekeeping including waste disposals is the primary functions of maintenance. Select one: O True O…

A: Maintenance  : The maintenance of equipment and buildings are the most important element of good…

Q: Explain the above : pressure sensor, pressure gauge and pressure transmitter with an application

A: Pressure is defined as the forces by the liquid and gas on the surface and it is measured in Newton…

Q: level sensors operate in a open control system. a. true b. false

A: It is false.  Ultrasonic level sensors operate in a close control system.

Q: Which of the following terms is not included in the mechanical energy balance? shaft work internal…

A:

Q: neutral plane

A: explanation shown below.

Q: Alternation and inspection of equipment are the secondary functions of maintenance. Select one: True…

A: This statement is false reason given below.

Q: A digital speedometer constantly reads 0 mph : TechnicianA says that the problem may be the…

A: Given Speedometer To find Which technician is correct

Q: Name three sources of information when conducting accident investigation

A: The three source of the information while conducting the accident investigation

Q: The pressure inside the aneroid is kept at sea level when it comes to the altimeter Smaller aircraft…

A:

Q: Need orthographic view  Use creo software on

A:

Q: Which of the following statements is FALSE? A. O Employees who use portable vibrating equipment such…

A: Here two separate questions has been asked. As per honor code and answering guidelines I can answer…

Q: Mention any four items must be available in the maintenance manual

A: Solution:

Q: Check stability help

A: Given data : The number of member=m=8 The number of joint=J=6 The number of external support…

Q: if the first digit of the diagnostic trouble code is zero what does it mean ?

A: Diagnostic trouble codes or also known as DTC, are the type of codes used by the vehicle…

Q: Activity: Lets' fix it! Directions: Read the following situations and explain why the motor of the…

A: As I understand from the question, I have to analyze all the three conditions and explain, why in…

Q: Choose correct answer: In hydraulic system circuit,the pressure gauge would not be available in the…

A: Gauge pressure: It is the difference between the absolute pressure and atmospheric pressure.

Q: Vacuum gauge, Ohm meter, Fuel pump, Ammeter

A: Instrument needed for Engine is vaccum gauge  A vacuum gauge shows the difference between outside…

Q: What are the different sensors and probes used in aircraft engine

A: Probes are used to collect information and sensors are supposed to perceive the information and…

Q: In creo parametric what is the name and job the following icons

A: Creo parametric is the 3D CAD software which  is optimized to meet the challenges faced by the…