What is interface. What is program block and module block.

Q: What are some applications for the logic synthesis tool?

A: • CPU: Applications can be implemented in software            and can be executed in one CPU. While…

Q: What are the five differences between microcontrollers and microprocessors?

A: Microprocessor is a basic element of the computer system. Microcontroller is a basic element of the…

Q: Briefly explain usage of Intel 8255A Programmable Peripheral Interface.

A: 8255A is a programmable Input/output device.

Q: Compare between SUB & CMP instructions

A: “Since you have asked multiple questions, we will solve one question for you. If you want any…

Q: Q2: Explain the role of Stack Register in 8086 Microprocessor.

A: the registers are used to store information in the microprocessor.

Q: The 8085-instruction set does not include a Clear Carry instruction. Which single-byte logical…

A: The 8085-instruction set does not include a Clear Carry instruction but it has set carry and…

Q: 6. Describe the operation of an OTE instruction.

A: OTE :  This is a instruction which is used in the PLC .       PLC : Programmable Logic Controllers.

Q: llustrate how external hardware interrupt on INTR pin of 8086/88 is tackled?

A: INTR is a type of maskable interrupt(means we can control or mask whenever any interrupt is…

Q: How does Arduino microcontroller differentiate an input logic signal 0 to logic signal 1 given a 5V…

A: Microcontroller is a pin device which contains Input/output ports and CPU for processing.

Q: Explain clearly the advantages and disadvantages of using Assembler when programming embedded…

A: Assembler is a software that converts Assembly low-level instructions into machine code, allowing…

Q: The 8085-instruction set does not include a Clear Carry instruction. Which single- byte logical…

A: I'm this question we will write instruction of clear Carry flag...

Q: 4) Suppose we have a 4-stage Johnson's counter, and its content is initially 1001. What is the…

A:

Q: Draw a block diagram of successive approximation ADC and explain its operation briefly.

A: Block diagram of successive approximation ADC

Q: 3. Draw the block diagram of an 8255 PPI chip and describe its different programming modes.…

A: block diagram for 8255 PPI is as shown in figure below

Q: Define architectural registers.

A: • Architectural registers is a type of internal register of the processor.• It is defined as those…

Q: Microprocessor 8085 : Note 1: Use F for fetch, R for memory read, W for memory write, IOR for IO…

A: In the 8085 Instruction set, SIM referred to as Set Interrupt Mask. 1-Byte instruction and also…

Q: 3. Draw a block diagram of Execution and Bus interface units of 8086 microprocessors.

A:

Q: Explain any five instructions with examples from data transfer group instruction?

A: The instruction is a binary pattern, which is designed inside a microprocessor to perform a…

Q: What is the use of OPERANDS and FLAGS in execution unit?

A: Here we have to explain the use of operations and FLAGS in execution unit.

Q: 41. F

A: Given Logic Circuit, f(A, B, C) = ?

Q: Compare the architectural features of an 8-bit and 16-bit microprocessor.

A:

Q: TTL output circuits are classified into two main kinds. What are these two sorts?

A: TTL output circuits classification

Q: What will be the BCD equivalent of decimal 15?

A:

Q: what is the advantages of memory segment.

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: show the classification of semiconductor memories.

A: Please refer the attached images for the complete answer..

Q: Explain the functions of the following registers associated with the MSP430 ports: (i) Direction…

A: As per Bartleby policy we can answer only three subparts. So I am answering first three for you.…

Q: he difference between the RET and RETI instructions? Explain why we can not use RET instead of RETI…

A: Both perform the same actions of popping off the top two bytes of the stack into the program counter…

Q: In IC 74153,the input at pin number 14 is Options A-Connected to ground B-Connected to power/VCC…

A: IC 74153 has two 4-by-1 multiplexers in it. A multiplexer has four inputs for input data, 2 lines…

Q: What Is the jobs done by registers inside a CPU

A: A register is each of a small set of knowledge-holding locations that are part of a pc processor. A…

Q: Q3. Briefly explain CISC and RISC processing unit architectures?

A: This is a simple question based on subject computer organization in electrical engineering . In this…

Q: Explanation about (Deal with operational amplifier controllers and programmable logic controllers)

A:

Q: A 16-bit successive approximation ADC is to be designed to operate at 50,000 conversions/second.…

A: Given  Nmax=50,000 conversion/s Calculating conversion time TT=1NmaxTT=150,000 conversion/sTT=2×10-5…

Q: Write a simple complete program with LOOP instruction for 8086 microprocessor, and explain the…

A: Loop instruction comes under the iteration control instructions. It's objective is to achieve…

Q: 1- Explain the meaning and operation of CMC instruction ?

A: Since, You ask Multiple questions but we are only allowed to answer one question at a time . so…

Q: Microprocessors; Explain the LOOP instruction with a simple example program for 8086…

A: For repeating a series of instructions, the loop instruction is used. The number of times for which…

Q: Write a Verilog code with testbench for 16-bit up/down counter with synchronous reset and…

A: Aim-we need to write a verilog code with testbench for 16-bit up/down counter with synchronous reset…

Q: How many flags are implemented in 8085 microprocessor?

A: In 8085 microprocessor, the flags register can have a total of eight flags. Thus a flag can be…

Q: Explain the ADD instruction of 8086. Compare it with ADC instruction.

A: Given that  Explain the ADD instruction of 8086. Compare it with ADC instruction.

Q: Mention what is PDC emulator and how would one know whether PDC emulator is working or not?

A: We have given the following problem Mention what is PDC emulator and how would one know whether PDC…

Q: Describe how the 'CMP' intruction/command works.

A: Given: CMP instruction/ command

Q: Q.19 Draw logic diagram for 4 to 1 line multiplexer. Q.20 Draw logic diagram for 1 to 4 line…

A: Solution: Logic diagram of  the 4×1 multiplexer is given as follows: Where,…

Q: Design a BCD to 7-segment converter by using logic gates?

A: We need to design a BCD to 7 segment converter by using logic gates.

Q: Browse for the datasheet of 8086 from Intel and using the information from datasheet answer the…

A: i) Draw the neat diagram of 8086:

Q: Design and draw the circuits that perform all the operations related to PC register , in a way which…

A: According to the question, we need to design and draw the PC register which performs all operations.

Q: In TTL, what are the two main kinds of output circuits?

A: The Transistor-Transistor Logic (TTL) is a BJT-based logic family (bipolar junction transistors).…

Q: What is the use of stack in micro-processor 8086?

A: Stack -  It behave as first in last outIt is a temporary data storage memory . Stack contain four…