What is reverse engineering and how does it work?

Q: 4- Can you trigger the TRAIC in (Q1 or QIv), explain briefly ?

A: Semiconductor are the material made of pure Si or Ge or compound . They have conductivity in between…

Q: 1. Are the theoretical calculations and measured values are equal? Explain?

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: Discuss how Inverter type generators are ensuring better voltage regulations?

A: An inverter generator produces alternating current (AC). The power produced by the alternator is…

Q: 41 4) obtain the analysis of the synchronous sequential circuit (State table and state diagram) in…

A: Output depends upon present input and present state hence it is mealy machine.

Q: What is the secondary post-processing/manufacturing steps?(After has been assembled and become a raw…

A: It is asked to discuss the secondary post-processing/manufacturing steps (the next stage after has…

Q: How can field distortion be remedied ?

A: Field distortion can be remedied by

Q: What is the effect of increasing k on time constant & error ? why?

A: Lets analyze it considering first order Transfer function…

Q: Draw the Direct Digital Control block diagram and show the Implementation of the Problem using a…

A: The block diagram of the direct digital control is shown below,

Q: 5. How you can operate a DC motor work with 3.7 volt ? Keep in mind that the motor is controlled by…

A: According to the question we have to discuss how we can operate a DC motor work with 3.7volt.

Q: Q1/ Design a circuit using an arduino board to control the direction and the speed of rotation of DC…

A: Design a circuit using an arduino board to control the direction and speed of rotation of DC motor…

Q: What is the reason for using numerical methods?

A: Reason for using numerical.methods

Q: Define stepper motor a. Explain the internal structure of stepper motor b. With Table explain the…

A: Stepper Motor Also called step motor/Stepping motor Brushless synchronous DC electric motor split…

Q: 1- What are the function of a) Execution unit b) Bus interface unit

A: As per bartleby guideline for more than one question asked only first is to be answered please…

Q: Type your question here • Analyze this circuit. • What about the output? • This circuit is an…

A:

Q: write a report about a comparison between state machines. In which, where we can use each type of…

A: There are two types of finite state machines. (a) Mealy state machine (b) Moore state machine…

Q: H.W: Write a short report about using internet of things (loT) in speed control of a three- phase…

A: The network in which physical matters are embedded with devices, sensor, network connectivity which…

Q: 3. Write any four differences between NC and CNC machines.

A: Ans. Given below

Q: Write more than a hundred words.About DC Machine

A: Electrical machine are classified as: AC Machine DC Machine An AC machine consist of transformer…

Q: Explain, how deflection torque is produced in PMMC Instrument.

A: In PMMC deflecting torque is generated by the electric current acting on the coil and the magnetic…

Q: What is Adaptive control system? If the process characteristics are not well known then what type of…

A: Adaptive control system is the control method which is used by a controller and which must adapt to…

Q: What is the difference between a Moore and Mealy machine? Sketch example state diagrams of each.

A: Moore Machine- In this machine, the machine reacts faster to inputs. In this machine, the output…

Q: n which year did 3D printing first become available to the public?

A: The idea of 3D printer was pitched in 1981 by Hideo Kodama of the Nagoya Municipal Industrial…

Q: (1) THE CONSTRUCTION OF DC MACHINE Aim: A simplified sketch of a dc machine and describe the…

A: DC Machine is further divided as DC Motor (which converts Electrical Energy to Mechanical energy )…

Q: ii. The generation voltage is in simulator is ...Volts.

A: In the simulator, the generation voltage and current source are showing on the display of the LED of…

Q: create an up counter written in verilog and running the simulation and test bench using the EDA…

A: To create the up counter using verilog :

Q: What is the purpose of fixturing and tooling in relationship to a robotic process?

A: Fixture is a support or work holding device used in the industry. Fixtures are used to securely…

Q: Provide state table for following state diagram, and design the mealy machine circuit diagram.

A: First, assign the states using binary encoding. It has 6 states, so required 3 D-flip flops.

Q: What does a compatible load mean? What if the load is not compatible?

A: This question is from "Power system and protection". Under which we are going to study load…

Q: Q1.Explain temperature compensation of strain gauge in detail?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Briefly describe the operation of the buck chopper.

A:

Q: Explain the meaning and give a practical significance of the unit step signal and ramp signal

A: Unit step signal  The unit signal is given by the mathematical expression as shown below:  f(t)=0 if…

Q: What can open-transition starting cause?

A: Open transition starting is a method of getting motor to its rated voltage by reduction of applied…

Q: What is voltage regulator?

A: The electronic devices we use in our life have some power ratings, voltage rating and current…

Q: Give information about this Transient stability of multi machine power system using UPFC

A:

Q: What are the advantages of performing ignition?

A: it is provided performance with reduced emission This system kept an coil that is ignition coil…

Q: 1.a. The typical PM work order is normally generated by a computer and then issued A. directly to…

A: 1(a). The typical PM work order is normally generated by a computer and then issued by the program…

Q: I opened a broken Coin Pusher Arcade game to fix, and I saw a burned IC. Between Microprocessor and…

A: An arcade game is a game machine which usually found in public places like malls, restaurants and…

Q: Signals and Systems. Show an example of shifting property with the help of proper CT signal…

A: According to the given question, it is required to determine the shifting property with the help of…

Q: Make a drawing/design of a block diagram of a synchronous sequential machine with its parts…

A: SEQUENTIAL LOGIC CIRCUITS: Sequential Logic circuits, unlike Combinational Logic circuits, have some…

Q: Explain 4x1 multiplexer? What is the difference between 2x1?

A:

Q: How does TP4056 works? What is the purpose of red and blue lights in the components?

A: The TP4056 chip is a single-cell lithium-ion battery charger that protects the cell against…

Q: Draw the DC Machine and label its parts

A:

Q: Jo S Q아 J1 Q1 4. FF FF Ko R O아 K1 R. 10 ICO

A:

Q: Explain Several design decisions exist with regard to instruction sets?

A: A set of native instructions that can only be carried out by hardware are defined by an instruction…

Q: Identify the troubleshooting procedures to determine the serviceability state of the circuits

A: Answer :- Trouble shooting of an electronic circuit is a process of having an inspiration on…

Q: Complete the blank Commutator in DC machine is made up of .....................................?

A: The commutator is the device used with the rotor in electrical machines to  ensure that current at…