Structure steel quest. What is the approximate value of the tensile strength governed by yielding ofthe cross section of a roof truss diagonal 100 x 75 x 6 mm (fy = 250 Mpa)connected to the gusset plate by 4-mm welds as shown in figure? (Take partialsafety factor as 1-10)1004 mm weld,140 mm longesa, = 1010 mm²75Weld 310 mm long

Given- Roof truss diagonal100×75×6 mmfy=250 Mpa4 mm welds It is needed to find the tensile strength…

What is the approximate value of the tensile strength governed by yielding of the cross section of a roof truss diagonal 100 × 75 x 6 mm (fy = 250 Mpa) connected to the gusset plate by 4-mm welds as shown in figure ? (Take partial safety factor as 1-10) 100 4 mm weld, 140 mm long Test,= 1010 mm² 75 Weld 310 mm long

What is the approximate value of the tensile strength governed by yielding of the cross section of a roof truss diagonal 100 × 75 x 6 mm (fy = 250 Mpa) connected to the gusset plate by 4-mm welds as shown in figure ? (Take partial safety factor as 1-10) 100 4 mm weld, 140 mm long Test,= 1010 mm² 75 Weld 310 mm long

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the stress area (in mm2) of each of the eighteen bolts used to fasten down the hemispherical joint of 480 mm pressure vessel having an internal pressure of 10 MPa, a material strength of 80 MPa and a bolt tensile strength of 150 MPa.
The thin uniform plate shown has a mass of 100kg and is subjected to a force and couple momentalong its edges. If it is supported in the horizontalplane by a roller at A, a ball-and-socket joint at B,and a cord at C, determine the components ofreaction at these supports to maintain equilibrium. Please provide all written work and show FBD. Thank you!
Please refer to the figure shown below. If P is equal to 8200 lb., and if all the rods have a cross-sectional area to be 0.4 sq. in. Explain why the set-up will fail or will not fail if the allowable stresses in Steel is 120MPa; 90MPa in Alumimun; and 100Mpa in Bronze. As the civil engineer of the project, if the set-up fails, provide a recommendation to prevent the failure to occur. Show your solutions to support your recommendation.
A steel plate (called a cover plate) having cross-sectional dimensions W2 5.0 in. x 0.4 in. is welded along the full length of the bottom flange of a W, 12.0 in. x 87.0 in. wide-flange beam (see the figure, which shows the beam cross section). I W2 cover plate What is the percent increase in the smaller section modulus (as compared to the wide-flange beam alone)? Round your answer to two decimal places. % in smaller section modulus =
The Aluminum plates below are connected by two 3/4" diameter bolts. What is the shear stress in the bolts given the load applied?
A hollow steel has an outside diameter of 5in. and it’s inside diameter is 4in. What is the thickness of steel? a.0.5 inb.1 inc.2 ind.0.6 in
Work out the quantity of steel in a 5m long simply supported beam of size 150 X 400mm overall. Bottom bar: 4- 10mm diameter straight bars. Anchor bar: 2-08mm diameter straight bars, stirrups 8min diameter @ 150mm cic throughout the length of the beam. Clear cover as 10mm on all sides.
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
Use virtual work method and determine the following unknowns on the truss system shown below. Use A = 500 mm2 and E = 200 GPa. Show complete and organized solution. Round-off your answers to two decimal places. GIVEN: a. 42.0 b. 4.0 c. 9.0 QUESTIONS: 1. Horizontal displacement of joint G due to the applied loads in mm 2. Horizontal displacement of joint G considering that the top chord members experience 60 oC increase in temperature in mm. Use α = 10-6/ oC PLEASE SHOW YOUR FULL SOLUTIONS AND DRAWINGS. THANK YOU VERY MUCH!! ❤️
The magnitudes of the three forces applied to the eye bolt are T1 = 100lb, T2 =50lb, and T3=170lb. Replace these forces with a single equivalent force R. Show the result on a sketch of theeye bolt.
please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 34 mm from the top of the of the beam on a section 1.66 m from A if P = 5381 N, W = 2349 N/m, a = 1.31 m, b = 2.12 m, c = 1.27 m, L = 72 mm and h = 239 mm. Round off the final answer to two decimal places.
1. The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm consists of two pieces. The pieces are prevented from sliding along the 55 degrees inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron in bearing and 345 MPa for the Key in shear. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key. Write your final answer in 2 decimal places with the unit of mm.