What is the approximate yield stress of the material shown Stress-Strain Curve 800 700 600 500 400 300 200 100 0.002 0.004 0.006 0.008 0.01 0.012 0.014 Strain, e (mm/mm) Select one: O a. 0.002 O b. 650 MPa O c. 0.02 O d. None of these options O e. 210 GPa O f. 500 MPa Stress, o. (MPa)

What is the approximate yield stress of the material shown Stress-Strain Curve 800 700 600 500 400 300 200 100 0.002 0.004 0.006 0.008 0.01 0.012 0.014 Strain, e (mm/mm) Select one: O a. 0.002 O b. 650 MPa O c. 0.02 O d. None of these options O e. 210 GPa O f. 500 MPa Stress, o. (MPa)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
8) Which of the following stress strain curve shows an elastic behaviour to very high strain rate a. cast iron b. Mild steel c. glass d. rubber
How can I solve for the %0.2 offset strain and the calculated stress? Original diameter : 6mm Original length : 30mm Fracture diameter : 4.54mm
PROPAGATION OF ERRORS Determine the range of values to which the strain will be calculated.F = 150000 +/- 150 lbfSide length = 1.2 +/- 0.025 inModulus of Elasticity = 25000 +/- 11.5 ksiDetermine the relative error. Is it above or below the accepted 5% relative error?
To determine the nominal or engineering stress and strain experienced by a specimen of a material while it is subjected to a tension test, and to be able to read important values from a conventional stress-strain diagram obtained from the test.A tension test is being conducted on a steel-rod specimen with a gauge length of L0=2 in and initial diameter of d0=0.5 in. Data were collected to form the conventional stress-strain diagram as shown. From the diagram, f = 73.0 ksi , e = 101.0 ksi g=83.0ksi, and h=0.15in/in Part A - Nominal or engineering strain in the rod Assuming that the strain remains constant throughout the region between the gauge points, determine the nominal strain ε experienced by the rod if it is elongated to L = 2.5 in . Express the nominal strain in inches per inch to three significant figures. Part B - Nominal or engineering stress in the specimen Assuming that the stress is constant over the cross-sectional area and if the tension force used is P = 8.0 kips ,…
Identify shortly the parts of the stress-strain. Briefly explain each part.
Choose the correct answer Stress divided by Rate of strain is: d. Velocity a. Surface tension f. Kinematic viscosity b. Density e. Dynamic Viscosity c. Unit less
A cast iron cylinder has outside and inside diameter 200mm and 125mmrespectively. If the ultimate strength of cast iron is 150MPa calculate according to each of the following theories of failure the internal pressure that will cause fracture.(a) Maximum principal stress theory. (b) Maximum principal strain theory. (c) Maximum strain energy theory. Assume no longitudinal stress in the cylinder. Which of the results obtained you consider should be applied to this case. Take:µ = 0.25, σU = 150MPa. Ans: (a) 65.73MPa. (b) 59.24MPa, (c) 55.33MPa.
To determine the nominal or engineering stress and strain experienced by a specimen of a material while it is subjected to a tension test, and to be able to read important values from a conventional stress-strain diagram obtained from the test. A tension test is being conducted on a steel-rod specimen with a gauge length of L0=50 mm and initial diameter of d0=13 mm. Data were collected to form the conventional stress-strain diagram as shown. From the diagram, f = 506 MPa , e = 689 MPa , g = 585 MPa , and h = 0.146 mm/mm . A) Assuming that the strain remains constant throughout the region between the gauge points, determine the nominal strain ε experienced by the rod if it is elongated to L = 53.0 mm . B) Assuming that the stress is constant over the cross-sectional area and if the tension force used is P = 16.0 kN , find the nominal stress experienced by the rod. C)Determine the force P needed to reach the ultimate stress in the steel-rod specimen.
Strain energy is the A. energy stored in a body when strained within elastic limits B. energy stored in a body when strained upto the breaking of a specimen C. maximum strain energy which can be stored in a body D. proof resilience per unit volume of a material
Determine the true strain and the final length of the operation
If the principal stresses on a material with a yield stress in shear are σ1 = 175 MPa and σ2 = 350 MPa, what tensile stress σ3 must be applied to cause yielding according to the Tresca criterion? b) If the stresses in a) were compressive, what tensile stress σ3 must be applied to cause yielding according to the Tresca criterion