what is the bolt bearing capacity of flange plate of the flange connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi effective bolt hole diameter = bolt hole + 1/16" beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in. Fexx=70ksi

what is the bolt bearing capacity of flange plate of the flange connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi effective bolt hole diameter = bolt hole + 1/16" beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in. Fexx=70ksi

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.2.6P

See similar textbooks

Related questions

Q: QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is…

A: Given data :

Q: 100 kN/m A 2m 2m 40 kN/m с 4m गी/D 120KN E 150 kN.m 2m

Q: 3. (a) Estimate the hydraulic gradient in a 2.2 m diameter smooth concrete pipe carrying a discharge…

A: Given- Discharge Q=3.4 m3/sDiameter of pipe D=2.2 mKinematic viscosity ν=1.004×10-6/secCoefficient…

Q: For the beam shown, EI = 24 × 10° kip-in² over the length of the beam. The slope (rad) of the beam…

Q: Answers: Ay Use the graphical method to construct the shear-force and bending-moment diagrams for…

Q: A compound curve has the following characteristics: 1₁ = 24° D₁ = 6° 1₂ = 36° D₂ = 4° Stationing of…

A: Given: Compound curve characteristics To find: Stationing of PCC Stationing of PC Note:…

Q: e moment distribution method to determine the moments at B and C.

Q: Determine the support reactions at point A and the force in the cable BC when the force at F is…

A: Given :

Q: Practical Part Q4). 1- State the meaning of normal consistency of cement. 2- Which method is widely…

Q: Construct the shear-force and bending-moment diagrams on paper and use the re ent parts of this GO…

Q: By direct integration, determine the moments of inertia of the triangular area about the x- and…

Q: Please show the complete solution. M A₂ 10' A L M B Answer: ly = i L 6 panels at 4' K L C L J D L MA…

A: To Determine Magnitude of Force Iy

Q: 9-111. The symmetric concrete "gravity" dam is held in place by its own weight. If the density of…

A: We have to calculate the smallest distance d at its base that will prevent the dam from overturning…

Q: The beam shown below is subjected to a factored uniform load of 8 kips/ft. The concrete strength is…

A: Shear strength of the beam Shear strength refers to a material or component's resistance to a…

Q: 2. The 9-kg paint stands on a wooden platform 1.2 kg in weight. Determine the magnitude and…

Q: 1. For the beam loaded as shown in the figure, a. draw the free body diagram b. determine the…

Q: 1.5 m 1.5 m T₂ 3 m B T₂ 4 m A T₁ 1 m 3 m

A: We have to find tension T1 and the final answer expressed in 3 decimal places in given fig.

Q: Define the fineness modulus of aggregate. What is it used for?

A: Aggregate:- Aggregate is used in building construction. It is generally two types coarse and fine.…

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings shown in the…

Q: The 450-kg mine car is hoisted up the incline using the cable and motor M. For a short time, the…

A: Given :

Q: 3. A road section to be laid out passes through a hilly terrain illustrated below. The section in…

Q: Problem 13.21 The 450-kg mine car is hoisted up the incline using the cable and motor M. For a short…

Q: W d OD g FA FB NOTE: angles c, d, f, g, are not drawn to scale X

A: Given FA = 185 lb FB = 189 lb Angles C = 7° D = 21° F = 9° G = 11°

Q: b) A one metre deep cut is excavated across an entire 3.0 acre site. The average bulk density of…

Q: 4.1 Results from liquid and plastic limit tests conducted on a soil are given below. Liquid limit…

Q: = A flat plate of width L = 1 m is pushed down with a velocity U 0.01 m/s towards a wall resulting…

A: Given- Length of flat plate=Lvelocity U=0.01 m/sAverage velocity Uavg needs to be find out.

Q: Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress…

Q: Problem 6.108 The wood used for the T-beam has an allowable tensile and compressive stress of…

A: Given :

Q: how did they get grid 1-4 under beams ?

A: Solution: For beam the X and Y are the cordinates where the moment are to be calculated: Grid X…

Q: as snow figure, exerted on the boom, for the equilibrium of the system. cable Figure

Q: Which type of lighting system has the highest life span?

A: The number of hours a lightbulb lasts varies based on the brand, innovation, and kind. The average…

Q: a. 9.30 kN b. 18.61 KN c. 37.21 AN d. 74.42 kN Compute the value of eccentricity e. 0.026 m 0.062 m…

Q: if the steel plate pictured above has a thickness of 5mm and a density of 5000 kg/m^3, find the…

Q: 9-111. The symmetric concrete "gravity" dam is held in place by its own weight. If the density of…

A: Given :

Q: Calculate for the axial force in kN at member DC of the frame shown in figure 2 using Cantilever…

A: Cantilever Method : A cantilever method is used to calculate the shear forces or bending moments on…

Q: need asap please

Q: Please show the complete solution. The signboard truss is designed to support a horizontal wind load…

A: To Determine Force in memebers BG & BF

Q: Classify the following soils by the AASHTO classification system. Give the group index for each…

Q: The top of the tower signal at B which is 2km away from A was sighted through a transit with…

Q: i 18" 10" 1.75" H in.

Q: The 28000-1b airplane is flying in the vertical plane at 390 ft/s. At the instant shown, the angle =…

Q: Part 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the…

Q: What is the deflection angle from P.C. to point A on the curve? Also Evaluate the length of curve…

A: Answer We are given R = 650 m Angle of Intersection ∆ = 60o We know that Deflection angle is given…

Q: 12 F2-10. If the resultant force acting on the bracket is to be 750 N directed along the positive x…

Q: Problem 1.4. A tensile test was conducted on a mild steel bar. The following data was obtained from…

A: Given data Diameter of steel bar (D) = 3 cm = 30mm Gauge length of bar (L) = 20 cm = 200 mm Load…

Q: Part A An aluminum 2014-T4 alloy bar 2.50 inches wide and 0.750 inches in thickness has a 1/4 inch…

A: Given, width of bar, t =0.750 inmaximum axial stress, σmax=7670 psib=2.50 ind=2×14 in=2×0.25 in

Q: Use the AREA method to construct the shear-force and bending-moment diagrams for the beam shown. Let…

Q: Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the…

Q: Determine the magnitude of the resultant force FR = F₁+F₂ and its direction, measured clockwise from…

Q: • A back tangent with bearing S 55° W meets a forward tangent with bearing N 15° W. What is the…

A: curves Curves are arcs with a limited radius that are placed between crossing straight lines to…

Concept explainers

Types and properties of steel

Steel is an alloy of iron. It is formed by heating iron and combining carbon (0.1-1.7%) with it and minor amounts of other elements such sulfur, chromium, manganese, nickel, etc. Thousands of steel grades have been published, registered, or regulated around the world, each with its chemical composition, and special numbering systems have been devised in various countries to classify the vast number of alloys.

Question

k) what is the bolt bearing capacity of flange plate of the flange connection in kips? (2 decimal places)

A992: Fy=50ksi, Fu=65ksi
A36: Fy=36ksi, Fu=58ksi
effective bolt hole diameter = bolt hole + 1/16"
beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.
Fexx=70ksi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction:

VIEW

Step 2: Calculate the Bearing capcity of the flanged plate:

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

an angle bar 100x100x11 mm tension member is connected with 20-mm-dia bolts as shown in the fig. both legs of the angles are connected. use fy=248 MPa and Fu=400 MPa. 1. determine the nominal strength for tensile yielding in the gross section. a. 515.59 kN b. 429.67 kN c. 545.60 kN d. 390.10 kN 2. determine the effective net area of member a. 1573 mm^2 b. 1632 mm^2 c. 1605 mm^2 d. 1815 mm^2 3. determine the nominal strength for tensile rupture in the net area. a. 642 kN b. 730 kN c. 554 kN d. 650 kN
12. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksil) what is the bolt bearing capacity of beam flange of the flange connection in kips? (2 decimal places)
A staggered riveted connection has rivets arranged as shown below. The plate is 400 mm and 12 mm thick with four bolt holes. The diameter of rivet is 34 mm The diameter of the rivet hole is assumed to be 5 mm larger than rivet diameter. Fy = 248 MPa. Fu= 410 MPa, Fv in rivets is 372 MPa. 1. Which of the following gives the distance b so that the net area in section 1 – 2 – 3 – 4 equal to the net area in section 1 – 2 – 4 a. 30.01 mm b. 25.12 mm c. 19.7 mm d. 12.23 mm 2. Which of the following gives the net area using the computed value of b. a. 4622.65 mm² b. 5623.75 mm² c. 3623.64 mm² d. 7652.85 mm² 3. Which of the following gives the maximum tensile force that the connection could carry if the allowable yield stress is Fy/1.67. a. 432.12 kN b. 724.73 kN c. 253.25 kN d. 712.81 kN 4. Which of the following gives the maximum tensile force that the…
Determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi l) what is the bolt bearing capacity of beam flange of the flange connection in kips? (2 decimal places)
9) what is the weld capacity of the shear connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
11. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksik) what is the bolt bearing capacity of flange plate of the flange connection in kips? (2 decimal places)
Determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi k) what is the bolt bearing capacity of flange plate of the flange connection in kips? (2 decimal places)
Determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksip) what is the tensile yielding capacity of flange plate of the flange connection in kips? (2 decimal places)
An A36 axially loaded 20mm thick tension member is connected to a gusset plate using5pcs 18mm diameter rivets arranged as shown. Use Fy= 248MPa & Fu=400MPa for thesteel plates. Given a=56mm, b=88mm, c=95mm, x=99mm, y=85mm and z=58mm. Calculate the allowable tensile strength (ASD) in KN based on Gross SectionYielding (GSY). Express your answer in 2 decimal places.
1.Use LRFD and design the tension members of the roof truss shown in Figure below. Use double-angle shapes throughout and assume 10-mm-thick gusset plates and welded connections. Assume a shear lag factor of U = 0.80. The trusses are spaced at 9 meters. Use A36 steel and design forthe following loads.Metal deck : 190 Pa of roof surfaceBuilt-up roof : 575 Pa of roof surfacePurlins : 145 Pa of roof surface (estimated)Roof Live Load : 960 Pa of horizontal projectionTruss weight : 240 Pa of horizontal projection (estimated) 2. Use A36 steel and design sag rods for the truss of Problem 1. Assume that, once attached, the metal deck will provide lateral support for the purlins; therefore, the sag rods need to be designed for the purlin weight only.a. Use LRFD.b. Use ASD.
10. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksij) what is the bolt shear capacity of the flange connection in kips? (2 decimal places)
Determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi d) what is the shear yielding capacity of the shear plate of the shear connection in kips? (2 decimal places)