What is the direction of the current in the wire if the zero point is 0.4 cm to the left of the wire? Out of the page. Into the page. Direction cannot be uniquely determined. Submit Request Answer • Part E What is the magnitude of the current in the wire if the zero field point is 0.4 cm to the left of the wire? Express your answers with appropriate units. HẢ ? I' = Value Units

What is the direction of the current in the wire if the zero point is 0.4 cm to the left of the wire? Out of the page. Into the page. Direction cannot be uniquely determined. Submit Request Answer • Part E What is the magnitude of the current in the wire if the zero field point is 0.4 cm to the left of the wire? Express your answers with appropriate units. HẢ ? I' = Value Units

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter22: Magnetism

Section: Chapter Questions

Problem 84PE: Integrated Concepts One long straight wire is to be held directly above another by repulsion between...

See similar textbooks

Similar questions

I could really use some help on some questions! The problem is as follows: A thine wire of length L carries a current I and is positional on top of the x-axis( see picture attached for clarification). The left of the wire lies on the origin. a) What direction is the B-field at point P? b) Determine the magnitude of the B-field at point P. (answer must be written in terms of L, I and a) c) Check the answer from part A by taking the limit L--> ∞ and comparing it to the magnetic field of an infinite straight wire, B=µ0I/2πr. The picture of the wire is attached below for visual. I appreciate the help!
Hi, please help me to solve this problem pls show the solution. Thank you very much. Keep safe QUESTION: A mysterious device found in a forgotten laboratory accumulates charge at a rate specified by the expression q(t) = 9−10t C from the moment it is switched on. Determine the current flowing into the device at t = 1 s,
Physics (Please, you can show all the steps explaining how to solve this problem. I do not fully understand this topic and I want to understand the procedure)A coaxial cable carries a current "I = 2 A". The inner conductor is a thin wire of radius "ρ = A = 0.5 cm" and the outer one has radius ρ = C =10 cm. It has a length h. between drivers there are two materials with permeabilities µ1 and µ2 as shown in the figure. (The purple area covers ¼ of the cylinder face and the orangezone ¾ ). Assume that the magnitude of the magnetic flux density inside the cable (both zones) is B = (1/ρ) in mT.a) Find (magnitude and direction) the magnetic field(s) H inside and outside the cableb) Make a diagram of the magnetic field lines inside and outside the wire.
A wire with resistivity ρ (resistance per unit length) is bended in a way to form a shape like bb-8 in the movie Star Wars. (See the figure on the right.) We can approximate it as two circles of radius R and 2R lying in the same plane. Note the wire has an insulating shell, and it crosses over itself at joint of the two circles. The wire is then placed in a magnetic field that is spatially uniform, but increases its magnitude over time with B = bt, where b is a constant of appropriate dimension. (a) What is the total resistance of the wire? Express your answer in terms of ρ and R. (b) What is the emf induced in the upper circle? In which direction? Express your answer in terms of R and b. (c) What is the emf induced in the lower circle? In which direction? Express your answer with R and b. (d) Find the net induced current flowing in the wire. Also specify the direction of the induced current. (It is better to indicate the direction by drawing arrows on the figure…
ASK YOUR TEACHER PRACTICE ANOTHER The figure below shows two vertical, parallel wires separated by a distance d = 11.5 cm. The left wire carries a current of I = 5.20 A upward, while the right wire carries a current of the same magnitude directed downward. Point P1 is a distance d to the right of the right wire, and point P2 is a distance 2d to the left of the left wire. Two vertical, parallel wires are separated by a distance d. To the left of the left wire is an arrow labeled I pointing up. To the right of the right wire is an arrow labeled I pointing down. A point P2 is a distance 2d to the left of the left wire, and a point P1 is a distance d to the right of the right wire. (a) What are the magnitude (in T) and direction of the net magnetic field at a point midway between the wires? magnitude T direction (b) What are the magnitude (in T) and direction of the net magnetic field at point P1, to the right of the right wire? magnitude T direction (c) What are the…
A square loop of aluminum wire is 17.0 cm on a side. It is to carry 12.2 Aand rotate in a uniform 1.24 Tmagnetic field as shown in the figure.(Figure 1) a.Determine the minimum diameter of the wire so that it will not fracture from tension or shear. Assume a safety factor of 10. b.What is the resistance of a single loop of this wire?
A rectangular loop of wire is placed next to a straight wire, as shown in figure below. There is a current of 4.3 A in both wires. Take a = 6.0 cm, b = 11.0 cm and c = 3.0 cm. Determine the magnitude and direction of the net force on the loop. (Choose toward wire direction as the positive and express the direction of the net force by using plus or minus signs in the result, which must be in multiples of 10 -6 Newtons and includes 2 digit after the decimal point. That means if you get a result of a 9.22 x 10 -6 and the direction of the net force is toward the wire, just type 9.22 or if you find the direction of the net force as opposite to the wire, just type -9.22 in the answer box. Maximum of 4% error accepted in your answer. Take vacuum permeability µ 0 = 4π x 10 -7 T /A 2 and π = 3.14.)
Draw a sketch of the situation in Figure 22.30 showing the direction of electrons carrying the current, and use RHR-l to verify the direction of the force on the wire.
Integrated Concepts One long straight wire is to be held directly above another by repulsion between 1heir currents. The lower wire carries 100 A and the wire 7.50 cm above it is 10gauge (2.588 mm diameter) copper wire. (a) What current must flow in the upper wire, neglecting the Earth’s field? (b) What is the smallest current if the Earth’s 3.00105T field is parallel to the ground and is not neglected? (c) Is the supported wire in a stable or unstable equilibrium if displaced vertically? If displaced horizontally?
Consider the circuit in Figure 27.17 and assume the battery has no internal resistance. (i) Just after the switch is closed, what is the current in the battery? (a) 0 (b) /2R (c) 2/R (d) /R (e) impossible to determine (ii) After a very long time, what is the current in the batten? Choose from the same choices. Figure 27.17 (Quick Quiz 27.5) How does the current vary after the switch is closed?
Integrated Concepts (a) What is the direction of the force on a wire carrying a current due east in a location where the Earth’s field is due north? Both are parallel to the ground. (b) Calculate the force per meter if the wire carries 20.0 A and the field strength is 3.00105T. (c) What diameter copper wire would have its weight supported by this force? (d) Calculate the resistance per meter and the voltage per meter needed.
Explain why B=0 inside a long, hollow copper pipe that is carrying an electric current parallel to the axis. Is B=0 outside the pipe?