What is the fracture direction in a reservoir? a) Along the tensile stress and perpendicular to the normal stress 3 b) Along the maximum normal stress and perpendicular to the minimum normal stress c) Along the normal stress and perpendicular to the tensile stress d) Along the maximum tensile stress and perpendicular to the minimum tensile stress

What is the fracture direction in a reservoir? a) Along the tensile stress and perpendicular to the normal stress 3 b) Along the maximum normal stress and perpendicular to the minimum normal stress c) Along the normal stress and perpendicular to the tensile stress d) Along the maximum tensile stress and perpendicular to the minimum tensile stress

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter11: Fracture And Fatigue

Section: Chapter Questions

Problem 11.10P

See similar textbooks

Similar questions

A cylindrical steel pressure vessel 500 mm in diameter with a wall thickness of 25 mm, is subjected to an internal pressure of 6.5 MN/m2. (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 120 MN/m2? (c) If the internal pressure were increased until the vessel burst, sketch the type of fracture that would occur
a. Explain using a typical stress-strain curve, the effect that cold working has on the yield strength and ductility of a mild steel specimen. b. Sketch a typical fractured specimen of a flat ductile mild steel bar which has failed when subjected to axial tension, showing clearly the region of fracture. c. Sketch a typical fractured specimen of a flat brittle cast iron bar which has failed when subjected to axial tension, showing clearly the region of fracture.
With neat sketches show three modes of fracture in a cracked material
Answer the questions given the following stresses: d) The value of the shear stress at any plane inclined at any angle with the horizontal is e) The value of the normal stress at any plane inclined at any angle with the horizontal is
A round bar of 25mm in diameter undergoes a tensile load of 120kpa. The gage length is 30cm and fracture length is 33.54cm.Compute the axial strain every 10mm and the total elongation after fractured.
Show that a tension crack will not appear in a saturatedclay if a surface stress of qs ≥ 2su is present. solve step by step please.
Briefly describe the physico-chemical parameters that control the ductile and brittle behavior of rocks under stress
Refer to the figure 1. Which of the following most nearly gives the value of the major principal stress? Answer: 216 kPA 2. Which of the following most nearly gives the value of the normal stress on the plane AB? Answer: 174.64 kPa 3. Which of the following gives the value of the shear stress on the plane AB? Answer: 54.64 kPA
Assume that a punch having a diameter of 20mm is used to punch a hole10mm thick plate. If a force P = 120KN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the punch?
A cylindrical pressure vessel is fabricated from steel plates which have a thickness of 20 mm. Thediameter of a pressure vessel is 500 mm and its length is 3.0 m. Determine the maximuminternal pressure which can be applied if the stress in the steel is limited to 140 MPa. If the theinternal pressure were increased until the vessel burst, sketch the type of fracture which wouldoccur. Write in a paper with complete solution
1)For a thick walled cylinder subjected to internal pressure only, Mention the surface where the shear stress happens to be maximum. Mention the other two stresses which are maximum at the surface of maximum shear stress. 2)What is the importance of the maximum shear stress for thick walled cylinders?
Determine the cracking moment of a rectangular concrete beam that is 18-inches tall and 6-inches wide. Take f’c as 5000 psi. Next, draw the normal stress distribution through the cross-section of the beam and label the minimum and maximum stresses on the normal stress distribution Diagram. What is the new moment of inertia (Ig) of the beam if during a flexure test, the tension face of the beam developed a 2-inch deep crack, but was quickly unloaded and did not completely fail?