What is the manufacturing tensional yield strength (lbf) of grade S135 drill pipe? a. This is a trick question because drill pipe size is not provided b. The answer can’t be calculated because the length of the pipe is not given c. The yield strength is 135000 psi and is a property of the steel d. The yield strength is 135000 psi and depends on the cross-sectional area

What is the manufacturing tensional yield strength (lbf) of grade S135 drill pipe? a. This is a trick question because drill pipe size is not provided b. The answer can’t be calculated because the length of the pipe is not given c. The yield strength is 135000 psi and is a property of the steel d. The yield strength is 135000 psi and depends on the cross-sectional area

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.4.5P

See similar textbooks

Similar questions

A full forming P= 50 kN axial force acts on the part shaped by the machining method made of xCy steel material. The thickness of the part is t= 20 mm and the steel tensile strength is sigma(tensile) = 600 MPa . Calculate the individual fatigue life of the A and B sections of the machine part for 90% reliability. Draw logarithmic S_N diagrams.
A bracket has been loaded as shown in figure. Compute the top and bottom fibre stress at section AB
A W18×86 beam is riveted tona W24×117 grinder by q connection as shown in the figure. The diameter of the rivets is 7/8 in, and angles are each 4×31/2×3/8 in. For each rivets assume that the allowable stresses are T= 15 ksi and stress in b is 32 ksi. What is the bearing strength of the grinder? What is the bearing strengtht of the beam? What is the shear strength of the rivets? What is the maximum load that the connection can carry?
The center post B of the assembly has an original length of 124.7 mm, whereas postsA and C have a length of 125 mm. If the caps on the top and bottom can beconsidered rigid, determine the average normal stress in each post. The posts aremade of aluminum and have a cross-sectional area of 400 mm Eal = 70 GPa. Detailed solution pls. Thank you!
A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
Solve Sample Problem No. 1 using these load values: a. M D =175 kN-m,M L =1 90 kN-m b. Find the maximum design moment so that its tension controlled. (USE c = 3d / 8). Tension steel exactly experiences 0.005 strain.
Strength of materials - ENGR 3321 The answer should be: 17.68 kN; 11.8 MN/m2 compressive
Please show intermediate steps including free body diagrams, equations used, and problemsetup so that your approach can be followed. A nylon thread is subjected to a 2-lb tension force. Knowing that E = 0.5 x 10^6psi and that the maximum allowable normal stress is 6 ksi,determine (a) the required diameter of the thread, (b) the corresponding percent increase inthe length of the thread.
The gas storage tank is fabricated in the following manner: a 10-mm thick plate is rolled to form a cylindrical shell which is bolted on one side, then its ends are sealed by bolting two hemispherical shells. The resulting inner diameter of the tank is 4 m. All bolts have a diameter of 15 mm. If the internal pressure in the tank is 1 MPa, determine the following:a. the number of bolts needed in each hemispherical shell if the normal stress in the bolts should not exceed 250 MPab. the minimum required thickness of the hemispherical shells if the normal stress in the shell should not exceed 125 MPac. the hoop stress in the cylinderd. the minimum require spacing of the bolts in the cylindrical shell if the normal stress in the bolts should not exceed 250 MPa.
For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is 140 MPa. Assume the plates are adequate to transmit the load to the rivets. P= 60 KN. a) Determine the shearing stress in the most stressed rivet. b) Determine the maximum allowable value of P. c) If P=80 KN, determine the minimum diameter of rivets. USE NSCP 2015. Thanks.
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten A plate having a width of 400 and a thickness of 20mm is to be connected to two plates with thickness of 12mm by four rivets. The allowable shear stress for the rivets is 150 MPa and for bearing is 1.35 Fy. If the yield strength and the ultimate strength is 248 MPa and 400 MPa respectively. Determine the Following: a.) Required diameter of rivets w/o exceeding the aloowable stress in the shear. b.) Required diameter of rivets w/o exceeding the allowable stress in bearing. c.) Required diameter of rivets w/o exceeding the allowable stress in tension.
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The plate shown is fastened to the fixed member by eight 16-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 80 MPa. If P = 8200 N, what is the maximum and minimum shearing stress developed in the rivet.