What is the maximum output voltage of a 3-4bridge rectifier supplied with line voltage of 440 V?(a) 528 V(c) 594 V(b) 396 V(d) 616 V

we need to find out maximum voltage.

Answered: What is the maximum output voltage of a…

What is the maximum output voltage of a 3-o bridge rectifier supplied with line voltage of 440 V? (a) 528 V (c) 594 V (b) 396 V (d) 616 V

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Related questions

Q: Thyristor H100 오 Diode R1, V, = 24 V( 10 KQ 4.7 KQ 1100 Ω Half-wave controlled rectifier with…

A: Types of SCR Triggering Method Forward voltage triggering Light Triggering dv/dt triggering Gate…

Q: what is the peak voltage of the input signal (Vp)?

Q: (1) Determine the output voltage of the DAC (digital-to-analog converter) if the input is…

Q: Draw the circuit of a voltage supply comprised of a full-wave bridge rectifier, capacitor filter,…

Q: A semi-controlled bridge rectifier with a resistive load is fed from XVRMS AC source. For the given…

A: We need to derive the average output voltage and normal average voltage for a single phase…

Q: Explain the operation of a 3-bit counter type Analog to Digital Converter with an example for 2.3 V…

Q: The gate current of a SCR half-wave rectifier is adjusted to 1.25mA and the forward breakdown…

A: For given gate current ,SCR starts conducting when anode to cathode voltage greater than 110 volts.…

Q: A single phase fully controlled bridge rectifier circuit has DC output voltage 170 V for an AC…

A: DC output voltage in case of converter=2×Peak voltage in supply wave formπ. DC output voltage in…

Q: What input voltage is needed in a bridge rectifier circuit to have an output of 10Vp?

Q: A single phase fully controlled bridge rectifier circuit has DC output voltage 165 V for an AC…

A: In case of inverter mode DC output voltage =-2×Peak voltage in supply wave formπ. In case of…

Q: For Ideal controlled rectifier which one of the following statement is correct? O a. RF and THD…

A: D . FF and TUF equal to unity .

Q: (a) The bridge full-wave rectifier with R-L load is designed using such parameters: input voltage =…

A: dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: A full-wave bridge rectifier is operated from a (50 Hz), (220 Vrms) line voltage. It has a (100 µF)…

Q: A single phase fully controlled bridge rectifier circuit has DC output voltage 150 V for an AC…

A: Average output voltage in converter mode=2×Peak value of supply voltageπ. In case of inverter mode…

Q: If the filtered load current is 10 mA, which of the following has a diode current of 10 mA? * a.…

A: In this question, choose the correct option If filtered load current = 10mA What is diode current of…

Q: 2) An SCR half-wave rectifier has a forward breakdown voltage of 150 V when a gate current of 1 mA…

A: Given parameters: For given SCR, Forward Breakdown voltage, Vb = 150 V Gate current, Ig = 1 mA The…

Q: R *20V 4R D, Draw the transfer characteristic of above precision rectifier circuit. [Assume diode…

Q: The 6 bit DAC has a 101101 INPUT and a 10 volt reference voltage. a. Determine the output voltage b.…

A: Most of the Electronics equipment works on the digital signal but we have analog input with us. To…

Q: Q4:-What is the fire angle that required to design an R-triggering circuit for a half wave…

A: In the given question we note that Igt(min) = 0.5mAVgt(min) = 0.7mAVd = 0.7VSupply voltage is…

Q: Q4. For the following bridge rectifier circuit, draw the output voltage waveform

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: A PMMC instrument with FSD = 50µA and Rm =2.2k2 is to be employed as an ac voltmeter with FSD=220V…

A: The basic circuit for enhancement of voltmeter is as shown below:

Q: Determine the output voltage of the D/A converter for the following digital inputs. Given a logic 0…

Q: Q4 (a) List TWO (2) advantages and TWO (2) disadvantages of a digital instrument compared to analog…

A: Note: We are authorized to answer one question at a time since you have not mentioned which question…

Q: Q4) If fr is the frequency of the fundamental component of the output ripple, then for full bridge…

A: In full wave bridge rectifier the time period of output signal is half of the time period of input…

Q: 3) Solve the following for a single phase half wave controlled rectifier supplied from a source of…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: b.for Bridge fullwave rectifier ,draw circuit diagrm and find Vde, Vrms & Vripp when Vin-30Vac.

A: The solution can be achieved as follows.

Q: Determine the output voltage of the D/A converter for the following digital inputs. Given a logic 0…

A: The signals understood by the machines are digital signals. The signals understood by humans are…

Q: For L load uncontrolled rectifier, draw the grah of the output current and output voltage.

A: For L- load uncontrolled Rectifier To draw the graph of output current and output voltage

Q: Using 4-bits successive approximation A/D converter, explain (with sketching the required figures)…

A: Here it is asked to convert 13 from analog to digital using SAR type A/D. Here the step size is 1.

Q: The gate current of an SCR full-wave rectifier is adjusted to 1.2mA and the forward breakdown…

A: Given gate current of 1.2 mA and corresponding break over voltage is 150 volts so scr starts…

Q: The sensitivity of a PMMC instrument is 10k /V. If this instrument is used in a rectifier type…

A: Given, For a PMMC instrument Sensitivity, Sdc = 10 kΩV

Q: What are the dc output voltages V1 and V2 for the rectiﬁer circuit shown. if vI = 40sin377t and C…

A: Draw the circuit diagram for the negative half cycle.

Q: Draw the circuit diagram of DC power supply of 12 V output by using Full wave rectifier center tap…

Q: Draw the circuit of a voltage supply comprised of a full-wave bridge rectifier, capacitor filter,…

A: Power Supply circuit has a wide range of application in the field of electronics. In electronics we…

Q: The gate current of a SCR half-wave rectifier is adjusted to 1.25mA and the forward breakdown…

A: Given Data: gate current = 1.25 mA Forward breakdown voltage = 110 V Applied voltage Vm = 220 V RL =…

Q: QUESTIONS 1. There are two functions of a transistor, that are fundamental to the design of…

A: A transistor is a semiconductor device used to amplify or switch electronic signals and electrical…

Q: A 4:1 transformer is connected to a bridge rectifier circuit with a 1kΩ load. What is the peak…

A: First we will find out output voltage then output current .

Q: A single phase full bridge inverter has RLC load of R=4 ohm, L=35 mH, and C=155 uF. The DC Input…

A: Solution: For a single-phase full-bridge inverter with RLC load…

Q: A regulated source has an input of 135 Vrms at 60 Hz, transformer ratio 0.1, output VDC 12V and load…

A: We can draw the circuit as given below Given that

Q: In a capacitor filtered bridge type rectifier circuit, what is the behavior of the circuit if (a)…

A: a) Capacitor is Shorted: In bridge type filter if capacitor is Shorted then voltage across the load…

Q: A full-wave bridge-type rectifier has a secondary maximum voltage of 20 Vm (peak) and a 4.7 kQ load…

Q: A silicon controlled rectifier (SCR) has a forward breakdown voltage of 230 V. When a gate current…

Q: A 5-bit flash converter has a reference voltage of 16 V. What is the digitized output of 10.12 V?

A: The solution is given below

Q: A sinusoidal voltage of 50 V (Vrms) and frequency 50 Hz is applied to a half wave rectifier. RL =…

A: Given, Vin=50 Vf=50 HzRL=200 ΩRF=20 Ω

Q: What is the peak load voltage out of a bridge rectifier for a secondary voltage of 12.6 Vrms? (Use…

Q: Q3/ Design a 3-bit flash ADC, what is the output digital word when the reference voltage is (8 volt)…

Q: Q4-What is the fire angle that required to design an R-triggering circuit for a half wave controlled…

A: Given, Igt(min)=0.5 mAVgt(min)=0.7 VVd=0.7 VSupply voltage=30 Vfrequency f=50 HzResistance in gate…

Q: Find the required input voltage of a half-wave rectifier with a 10.5V output voltage

Question

What is the maximum output voltage of a 3-4
bridge rectifier supplied with line voltage of 440 V?
(a) 528 V
(c) 594 V
(b) 396 V
(d) 616 V

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the difference between a diode and rectifier?
Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
Explain the operation of an analog voltmeter.
What is CEMF?
How is a solid-state diode tested? Explain.
Q/ What is the difference between single phase full wave controlled and uncontrolled bridge rectifier.
In a full-wave bridge rectifier equivalent DC output voltage circuit, calculate the effective DC voltage output given a Vin(RMS)=110 V (60 Hz) and the turns has a ratio of 10:1. Explain each step of your calculation briefly.
For L load uncontrolled rectifier, draw the grah of the output current and output voltage.
What input voltage is needed in a bridge rectifier circuit in order to produce an output voltage of 10Vp
The gate current of a SCR half-wave rectifier is adjusted to 1.25mA and the forward breakdown voltage of SCR corresponding to this gate current is 110V. The applied voltage is 220V, the load resistance is 150 ohms and the holding current is zero. Determine the a) firing angle b) conduction angle c) average output voltage d) average current and e) average power (Our lesson is POWER ELECTRONIC DEVICES in the subject INDUSTRIAL ELECTRONIC)
Draw a rectifier circuit with a power factor is 1. Indicate the circuit features
1- Connect the Full-wave Bridge Rectifier with resistive load (RL=15kΩ)and set the parameters value of peak amplitude equal (200) volt, frequencyequal (50) HZ .2- Draw the output waveform for the DC output and the r.m.s value of theoutput voltages.3- Calculate the ripple factor (r) for the value of RL.