What is the maximum shearing strain on the shaft

Q: The shear center is the point through which a force can be applied which will cause a beam to bend…

A: The shear center is defined as a point on which an applied external load does not create any twist…

Q: Draw Normal force, shear force and Bending moment Diagram

A: Given:- P=48kips AB=12' BC=12' CD=16' BE=10' To find: To draw 1) Shear force diagram 2) Normal force…

Q: The increase in size of the hole in a metal plate that is contact with a bolt is an indication of…

A:

Q: (4) The average flow stress is the flow stress multiplied by which of the following factors: (a) n,…

A: “Since you have asked multiple question , we will solve the first three questions for you. If you…

Q: 10. What is the minimum diameter in mm of a steel shaft which will be used to operate a 14 kN-m…

A:

Q: What happens if the torsional loadings applied to the shaft?

A: When the torsional load is applied on the shaft, the shear stress is produced in the shaft, and this…

Q: ser % and 905

A:

Q: Which et h

A: introduction: Forging is a manufacturing technique that involves pounding, pressing, or rolling…

Q: What happens when a shaft having a circular cross-section is subjected to a torque?

A: When the torque is subjected to the shaft, the shear stress is generated in the shaft, and this…

Q: Determine the stress area of a 2 in. triple Buttress thread power screw that has a lead of 3 5 in.

A:

Q: What is the discontinuity of loading?

A: The load along the length of the structure, say a beam if is consistent then we can say that the…

Q: --------stresses are induced in the shafts if the shafts are manufactures by cold drawing process.

A: Drawing is a process in which a metal is stretched through a die using tensile forces.

Q: The shear force is maximum at the sign change in a simply supported beam. Select one: True…

A:

Q: How can the angle of twist of one end of a shaft or tube with respect to theother ends be…

A: Given Data: The length of the shaft is L. The diameter of the shaft is d. The moment acting on the…

Q: Draw shear force and bending moment diagrams

A:

Q: shear strain produced during the operation

A: Given; Feed given to the zero degree rake angle tool is=0.2 mm/revWhere, During pure orthogonal…

Q: Can the segments of the shaft be subjected to different internal torques?

A: The internal torque on a shaft can be varied according to the cross-sectional area. The torque can…

Q: subjected to varying bending moment along its length?

A: Given; From given fig;Distribution transverse shear stress across depth h of a rectangular beam…

Q: What is the Shear Load on the left of point A to point A itself? * -15 kips -25 kips -10 kips O -18…

A:

Q: mm. When subject to pressure, the hoop stress in

A:

Q: just to clarifay is the shaft stainless steel? or the tool making the threads on the shaft

A: It is the shaft which is made up of stainless steel.

Q: When is a bending moment: positive or negative?

A: To define when the bending is positive and negative

Q: w = 35 kN/m 38-mm diameter 38-mm diameter 150-mm diameter 100 mm 300 mm 100 mm

A:

Q: The twisting moment and flexural rigidity of the shaft are the same. Select one: True False

A: False

Q: 3) Docs the nodal point have the maximum or minimum stresses along the shaft, why?

A: We have given the problem

Q: 16) Earing is a type of defect, usually found in 17) Tension is the only type of stress applied in…

A: we have to fill in the blanks

Q: Determine shear plane angle.

A: Given; In a turning process using orthogonal tool geometry, Chip length,l=100 mmUncut chip…

Q: e bending stress :

A: option. c  - 3.38

Q: ring stress in the head of the bolt: of the washers if their inside diam

A:

Q: 9 - A power shears is used to cut soft cold rolled steel that is 4.75 mm thick. At what clearance…

A: Answer: (f) 0.285

Q: What is a bending moment?

A: Bending moment: Bending moment is a moment which developed in any structure or body when a force or…

Q: 2. Hooke's law holds good upto A.Yield point B.Limit of proportionality C.Breaking point D.Elastic…

A: To explain the Hooke's law limits

Q: Radius of Mohr's circle representing the given state of stress

A: Given; State of stress  at a point under a plane stess condition:  σx=40 MPa  σy=100 MPa  ζxy=40…

Q: what is the unit of stress?

A: stress can be defined as the ratio of the applied and the cross-sectional area.

Q: The shear angle

A: Given data: An ortogonal turning operation is carried out under the following condition: Rake…

Q: How is the angle of twist of a circular shaft determined?

A: Angle of twist When the torsional load is applied on the free end of the shaft, then the fixed end…

Q: The shearing stress at point P

A: Dear Student kindly refer attached files.

Q: What is the hoop stress?

A: What is hoop stress

Q: flange bolt coupling is used to connect two solid shaft 125 mm in diameter. If the shearing stress…

A:

Q: What would be the maximum torque T' if a 75-mm-diameter hole were bored through the shaft?

A: (A) The calculation for maximum torque: - From the torsion equation, the formula for torque is given…

Q: What is the cause of shear in a member?

A: Shear Force: Shear force is due to the force that is applied to the member which acts along the…

Q: How large a hole can be bored in a 4 in diameter shaft without increasing the maximum shear stress…

A: Answer: The largest hole thay can be bored in a 4 in diameter shaft without increasing the maximum…

Q: Determine shear

A: Given; Chip thickness ratio of the metal cutting of MS is;  r=0.5Where, Orthogonal cutiing of MS…

Q: the maximum multiplication energy

A:

Q: Which of the following statement is false related to the theory of simple bending.   The…

A: Opption (d) The value of Young's modulus is not same  is correct option

Q: total true longitudenal strain in the rod

A: Given; A rod of length, l=20mmit is stretched to make a rod of;Length, l=40 mmIt is compressed to…

Q: 50 kN

A: given:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.