What is the other name of 1 × 4 Demultiplexer? And what is mean?

Q: nd peak time. Al t overshoot? [Sect

A: t=0fv=14-secondK=117% overshoot

Q: wharmonics a

A: ANSWER- n=3

Q: In a CNC feed drive, a stepper motor with step angle of 1.8 degree drives a lead screw with pitch of…

A: Given data  Step angle θ= 1.8°  Pitch P= 2mm

Q: Discuss the principle operation of the AVR?

A: AVR stands for the automatic voltage regulator. It is an electronic device that automatically…

Q: Define the T ds RELATIONS

A:

Q: What are the control methods for electromechanical systems. What are the advantages of each method?

A:

Q: Define the term effective length?

A: Effective length – it is defined as the distance between the bottom and top of the column at the…

Q: 2. Explain the advantage and disadvantages of DuFort-Frankel and Crank- Nikolson methods.

A: In numerical analysis, the Crank–Nicolson method is finite difference method used for numerically…

Q: Discuss different design of aspects of PEV, BEV and HEV with suitable diagrams?

A: Hybrid electric vehicle: HEVs are the most common type of hybrid, and they have been around the…

Q: Explain the purpose of HT coil and HT leads mention why leads are not made with metal

A: Purpose Of HT leads: In I.C. engine to connect Spark plug each of the distributors.  To connect…

Q: Define the term Torque?

A: Torque: Torque is defined as the multiplication of the force and force-distance from the given…

Q: A three-pole contactor would allowhow many paths for current flow?

A: A  three-pole contactor is a device used to turn off or turn on the three phase load. When the…

Q: 5- What are the main components of DC-sputtering device with schematic?

A: Solution is attached below

Q: @ Déscuss MDethenol as a luel is the Transpustation sector

A:

Q: State and exolain Grashof's law for four-bar mechanis in detail

A: In a Four link mechanism, a four-bar linkage forms a closed loop and this can be further used in…

Q: What is restitution impulse?

A: Fig.1   Consider two bodies A and B of mass M as shown in Fig.1. When body A strikes to body B, a…

Q: What do the acronyms EAC, SCC, HE, and LME stand for?

A: Environmental assisted cracking(EAC) refers to brittle fracture of a ductile material due to…

Q: Explain the working of a cascade impactor and make its schematic diagram?

A: Cascade impactor is a particle collection device, widely used to investigate little particulates in…

Q: In terms Poisson's ratio

A: Given;   In terms of Poisson ratio, μYoungs modulus, EShear modulus, GSo we have to find elastic…

Q: Find tension in AC and W?

A: Consider the diagram shown below for the given system.

Q: What are the mechanical problems are associated with an ESP?

A: Given ESP To find Mechanical problem

Q: Discuss on main types of accumulators and explain any one with neat diagram.

A: Accumulators - It is part of hydraulic system which store hydraulic energy in the form of…

Q: FOS as per Goodman's relation.

A: Given; A thin spherical pressure vessel of;D=200 mmthickness,t=1 mmInternal pressure varying from= 1…

Q: What is gyrocompass?

A: Gyrocompass It is a non-magnetic compass used for determining the heading of a vehicle. The…

Q: Hi can anyone tell me why the summation of Fx=-300sin(30)+150 instead of Fx=-300cos(30)+150?

A:

Q: Make the definition of Spring Pin and what are the advantages and disadvantages

A: Spring Pin: It is an mechanical fastener. Spring pin is used to tight the relative positon of  two…

Q: What are the advantages of cold-side ESPs over hot-side ESPs?

A: Electrostatic precipitators(ESP)  are devices which are used to remove dust and smoke particles from…

Q: Explain where did 23.4 came from

A: Use linear interpolation technique to calculate saturation pressure at 20 degree Celsius.

Q: Explain the following type of end effectors: i. Magnetic gripper ii. Spot welding device

A:

Q: Define the term redundant?

A: Answer :- Many times people get confused between Redundant and Repitition. But redundant does not…

Q: Hinged at both ends. Find : (2. TcD = ?. (3) O LT=?

A:

Q: What is the difference between force transmissibility and motion transmissibility?

A:

Q: What is an attenuator used for?

A:

Q: What is a coupling

A: Coupling is a commom word used in the field of mechanical engineering which means joining or…

Q: gh illustrations explain the process of TIG W

A: introduction: we  have to explain about TIG welding.

Q: 4- How AFM can be calibrated? 5- What are the components of SPM device?

A: INTRODUCTION : In order to maintain precise results, all microscopes must be calibrated. One of the…

Q: why does classical mechanisms failed

A: given; why does classical mechanisms failed

Q: What is Critical Point Transition?

A: In thermodynamics, a critical point (or critical state) is the end point of a phase equilibrium…

Q: (mechaniam structure and preloaded structure). [Fill the table gives below). of the systems shown in…

A:

Q: TOPIC: TORSION II IN measures how fast the revolution shaft connected to a is for a motor.

A: To name: The device used to measure the revolution of shaft connected to a motor. Explanation: The…

Q: Explain Thermocouple and Thermistor with necessary diagram and equations

A:

Q: OWhat's the linear actuator, Please list the types of linear actuators. Figure out their…

A: Solution:

Q: had a natural frequency of 20 cycles/second. What is the approximate fundamental frequency of…

A: Applying Dunkerly's principle, 1⁄(ω12)+1⁄(ω22)+1⁄(ω32) = 1/100 + 1/400 = 1/80 Therefore  ω1=80…