What is the overall capacity for the question in the image Product 130%ShapingMillingMillLathe15 units/hr50 units/hrPolishingPolishing Unit42 units/hrMillingMillProduct 265%31 units/hr70%35%MillingMill60 units/hrIn the process shown above, what islare) the bottleneck(s)?O Polishing UnitO LatheO Mil100FFlEFI0Rack oNceIN)7.8.TELEnter4.KFGShiftMCtrlAlt Gr

Bottlenecks are those process which slows the production Let the total number of units taken for…

Answered: What is the overall capacity for the…

Engineering

Mechanical Engineering

What is the overall capacity for the question in the image

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter2: Measurement, Materials, And Safety

Section2.5: Quality Assurance, Process Planning, And Quality Control

Problem 1RQ: What are the four basic parts of a process plan?

See similar textbooks

Similar questions

A HSS tool is used to turn a steel workpart that is 300 mm long and 80 mm in diameter. The parameters in the Taylor equation are: n = 0.13 and C = 75 (m/min) for a feed of 0.4 mm/rev. The operator and machine tool rate = $30.00/hr, and the tooling cost per cutting edge = $4.00. It takes 2.0 min to load and unload the workpart and 3.50 min to change tools. Determine: Tutting speed for maximum production rate, Tool life in min of cutting, and Cycle time and cost per unit of product. determine cutting speed for minimum cost.
(USCS units) A turning operation is performed using a rake angle of 15°. Cutting speed = 200 ft/min, feed= 0.012 in/rev, and depth of cut = 0.100 in. The chip thickness ratio measured after the cut = 0.48. Determine (a) chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain (USCS units) The turning operation in the previous problem involves a work material whose shear strength = 52,000 lb/in2. Based on your answers to the previous problem, compute (a) shear force, (b) cutting force, (c) thrust force, and (d) friction force.
Hello , i believe scale factor is 13 not 17. Does this affect the ongoing solution ? or if i just change the 17 to 13 ? Because ÖN= 5
For a particular process, suppose the bottle neck cycle time is 40, and the raw processing time is 100. What is the minimum number of customers that must be in the system in order for the lead-time (LT) to exceed the raw processing time? Round to one decimal place.
APPLICATIONS F MAXIMA & MINIMA1 . The profit derived from producing a certain product isp = 30x -X2-200 where X = number of product unitsproduced per month . What level of production will yielda zero marginal profit ?
A high-speed steel tool is used to turn a steel workpart that is 295 mm long and 75 mm in diameter. The parameters in the Taylor equation are: n = 0.15 and C = 80 (m/min) for a feed of 0.5 mm/rev. The operator and machine tool rate = $29.00/hr, and the tooling cost per cutting edge = $3.90. It takes 2.1 min to load and unload the workpart and 3.40 min to change tools. Determine (a) cutting speed for maximum production rate, (b) tool life in min of cutting, and (c) cycle time and cost per unit of product (d) cutting speed for minimum cost and tool life in min of cutting
Asap,
Orthogonal cutting, in a machining process,The attacking team sawdust (α) is 10 ̊. operationchip (t0) 0.5 mm and machining beforeAfter the chip coating (tc) is 1,125 mm.Accordingly, in machining;a) Slip plane (ϕ),b) Shear strain (γ) calculator
In a turning operation of stainless-steel work part having shear strength = 378 MPa and tensile strength = 420 MPa, a coated carbide tool with a rake angle of 5 degrees is used to reduce its diameter from 100 mm to 93.2 mm with a cutting ratio of 0.45. During this process, a cutting speed of 2.4 m/s and feed of 0.24 mm/rev is used. Using the orthogonal model to approximate the turning process, how much power (W) will the lathe draw in performing this operation if its mechanical efficiency = 90%.
The average number of articles produced by two machines per day are 200 and 250 with S.D 20 and 25 respectively on the basis of records of 25 days production.Can you regard both the machines equally efficient at 1% level of significant?
Three machines are used in a group-technology cell to process a family of five parts. Thetable below lists production quantities (Qj), production times (Tpij), and machine fractionsfor each family member (fij). Part E requires a changeover time of 5 min on each machine soit is produced in batches of 5 parts. Nonoperation times (Tno) are the same for all parts andmachines: 25 min per machine. Determine (a) average hourly production rate for the cell,(b) utilization of each machine and average utilization of the cell, (c) manufacturing leadtime, and (d) work-in-process. A spreadsheet calculator is recommended for this problem
The following data were obtained in a study taken on a horizontal milling machine:Parts produced per cycle: 8.Average measured cycle time: 8.36 minutes.Average measured stress time per cycle: 4.62 minutes.Average fast traverse time: 0.08 minutes.Average cutting time with electrical power: 3.66 minutes.Performance rating: 115%.Clearance (machine time): 10%.Slack (effort time): 15%.The operator works on the task 8 hours a day and produces 380 parts. How many standard hours does the operator work? What is the operator's efficiency for the 8-hour day?