What is the reliability value that should be used in the flexible pavement design equation if the goal is to ensure that serviceability will be maintained at adequate levels throughout the design life of the facility with 86% probability? (please provide your answer with at least 3 digits after the decimal place)

What is the reliability value that should be used in the flexible pavement design equation if the goal is to ensure that serviceability will be maintained at adequate levels throughout the design life of the facility with 86% probability? (please provide your answer with at least 3 digits after the decimal place)

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter21: Pavement Management

Section: Chapter Questions

Problem 12P

See similar textbooks

Similar questions

Rehabilitation methods of PAVEMENT CONDITION INDEX?
Determine the base thickness of plain concrete pavement (PCP) without dowelled joints using the information and charts provided be • Desired project reliability - 85% Subgrade design CBR-6% • Design period -30 years • Design Traffic 5.0*10* HVAG(B) Note: The information obtained from each table or figure must be stated in the examination script to obtain relevant marks. Table 3.1: Minimum subbase requirements for rigid pavements Design traffic (HVAG) Subbase type 125 mm bound Up to 10⁰ Up to 5x10 150 mm bound or 125 mm LCS Up to 1x10 170 mm bound or 125 mm LCS 150 mm LCS Greater than 1x 10 1 Under CRCP, a heavily bound subbase with an asphalt surfacing is an acceptable alternative 75 Maximum permitted value CBR % Effective subgrade strength used in concrete base thickness determinations 60 50 40 35 30 25 20 15 12 10 Concrete Base 200 Thickness 190 (mm) 180 8. Pavement type 7. 6. 5. PCP Dowelled & CRCP 260 250 240 230 220 210 170 160 150 140 150mm LCS 125mm LCS 8 10 Design subgrade…
Q#3. Discuss root causes and remedial measures of the following distresses occurring in flexible pavements: Slippage failure, Potholes, Rutting and its types, Bitumen bleeding Answer in word format
Q9. The preventive rehabilitation technique is that which involves: a) surface applications of either structural or nonstructural improvements intended to keep the quality of the pavement above a predetermined level b) all means that enables the designer to consider each maintenance alternative in terms of a final product and then select the most appropriate one in terms of results desired and cost. c) the permanent or temporary repair of deficiencies on an as-needed basis d) a and b e) b and c Q10. When compacting a soil at wet to optimum, then; a) the soil fabric is oriented and it has lower permeability b) the soil fabric is dispersed and it has lower permeability c) the soil fabric is dispersed and it has a higher strength d) the soil fabric is dispersed and it has a lower strength
An agency uses the following formula to determine pavement condition rating, PCR = 99.3 − 5.51 (5.0-ROUGH) − 1.59 LNALL − 0.221 AVGOUT − 0.0306 LONG − 0.531 TRAN, where we have the following. ROUGH = roughness measured by present serviceability rating (PSR), scale of 0 to 5 LNALL = natural logarithm of alligator cracking, ft per mile AVGOUT = outer wheel path rutting (all locations averaged), 0.01 inch LONG = longitudinal cracking, ft per mile TRAN = transverse cracking, number of cracks per mile And, present serviceability rating is determined as the following. PSR = 5e−0.0051118 · IRI − 0.0016027 A pavement section has the following distress data. IRI = 108 in./mi Alligator cracking = 110 ft/mi Average rutting = 0.20 in. Longitudinal cracks = 130 ft/mi Transverse cracks = 12/mi Determine the current PCR for this section. PCR = Now, assume a new roughness measurement is expected soon. When PCR falls below 60, the section will be scheduled for rehabilitation. Determine the new IRI…
Define pavement management system (PMS) and describe its benefits.
What data should be included in a network-level pavement management inventory and explain the use of each type of data.
Define precisely the difference between pavement serviceability and performance. Using a sketch to indicate the concept of remaining service life of a pavement segment.
DESIGN OF A RIGID PAVEMENT1. Give a summary of rigid pavement design procedure by AASHTO method (1993), anddescribe the variables used in the method.2. Explain the CBR test; how to conduct the test and its purposes. Where are the usages oftest results in practical applications? Explain its advantages and disadvantages.3. Determine the thickness of a rigid pavement (thickness of concrete slab) by using thedata provided below:DATA PROVIDED:1. Cumulative 18kips ESAL = 5.000.0002. Overall standard deviation = 0.33. Reliability = 95%4. Design serviceability loose =1.75. Drainage coefficient = 16. Load transfer coefficient = 3.27. Mean concrete modulus of rupture = 650 psi8. Elastic modulus of the concrete to be used = 5.000.000psi9. Results of CBR test on subgrade material in the laboratory (Table 1):10. Standard force-penetration data.
An agency uses the following formula to determine pavement condition rating, PCR = 99.3 5.51 (5.0-ROUGH) 1.59 LNALL 0.221 AVGOUT 0.0306 LONG where we have the following. ROUGH = roughness measured by present serviceability rating (PSR), scale of 0 to 5 LNALL = natural logarithm of alligator cracking, ft per mile AVGOUT = outer wheel path rutting (all locations averaged), 0.01 inch LONG = longitudinal cracking, ft per mile TRAN = transverse cracking, number of cracks per mile And, present serviceability rating is determined as the following. PSR = 5e-0.0051118 IRI-0.0016027 A pavement section has the following distress data. IRI = 106 in./mi Alligator cracking 110 ft/mi Average rutting = 0.20 in. Longitudinal cracks = 130 ft/mi Transverse cracks = 12/mi Determine the current PCR for this section. PCR = 0.531 TRAN, Now, assume a new roughness measurement is expected soon. When PCR falls below 60, the section will be scheduled for rehabilitation. Determine the new IRI value (in in./mi)…
What is Falling Weight Deflectometer? How it can be used to determine potential of voids in rigid pavements?
Discuss the strategy of pavement evaluation process in detail