Answered: What is the torque produced when a…

What is the torque produced when a force of 15N is applied to open the door that is 2.5 meters wide? Note that the point of application of the force is in the middle of the door .

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 83P: What is the torque abot the origin of the force if it is applied at the point whose position is:

See similar textbooks

Related questions

Q: A 50 N force is applied at the end of a 30 cm wrench. If the force makes an angle of 67° with the…

Q: Hera applied force on a wrench to loosen a pipe. If the wrench is 25 cm long and she applied 150 N…

A: Given data: Length of wrench (r) = 25 cm = 0.25 m Applied force (F) = 150 N Angle (θ) = 67°

Q: The bolts on a car wheel require tightening to a torque of 9 N∙m. If a 8 cm long wrench is used,…

A: Given data: Torque is, τ=9 N∙m The length of the wrench is, r= 8 cm= 0.08 m The angle between F and…

Q: A plumber needs to increase the torque to unfasten a pipe. How can they do this? O Apply more force…

A: Given:) torque required to unfasten a pipe required:) way to increase the torque

Q: A basketball is being pushed by two players during tip-off. One player exerts an upward force of 15…

A: net torque = upwards torque + downward torque net torque = (15)(0.14) + (11)(0.07)net torque = 2.1 +…

Q: Which is the torque having distance (meters) and mass (kg) for each of the data?

Q: If you are trying to loosen a stubborn screw from a piece of wood with a screwdriver and fail,…

A: Opening a screw

Q: A youngster who has entered a soapbox derby (in which 4-wheel unpowered vehicles roll from rest down…

A: As the moment of inertia is inversely proportional to the rotational speed, decrease in moment of…

Q: A force of 250 N is exerted on a cable wrapped around a drum that has a diameter of 120 mm. What is…

A: Answer:- Given Force (f) = 250 N Diameter (d) = 120 mm Radius (r) = Diameter/2 r = d/2 r = (120…

Q: What is the maximum length of a wrench needed to apply 90 Nm torque to the bolts on a motorcycle…

A: Given Torque T=90Nm Force applied F=200N

Q: A child with a mass of 25 kg sits at a distance of 1.8 m from the pivot of a seesaw. Calculate a.…

Q: Two equal and opposite forces each of magnitude 40N are applied to the rim of a wheel makes 12…

A: magnitude of forces are 40N . no. of revolutions 12.

Q: Can a force produce a torque when there is no lever arm?

A: The torque is the rotational force or the force that tends to cause rotation. The expression for the…

Q: The length of the pool cue is 1.5 m. A force of 27 N is applied a distance 0.9 meters from the…

Q: Suppose a force of 46 N is applied to a 0.11-meter-long wrench attached to a bolt in a direction…

Q: A square, 0.862 m on a side, is mounted so that it can rotate about an axis that passes through the…

A: When the force is applied to the perpendicular to the diagonal of the given square, that is its axis…

Q: A rod of Length 5R is fixed about a point 1/5th of the length from the right edge. All forces are…

A: In given figure 4 forces are applied on rod at different point. Torque = r × F = perpendicular force…

Q: A wrench 0.7 meters long lies along the positive y-axis, and grips a bolt at the origin. A force is…

A: Given data: Length of wrench along positive y-axis is, r=0.7 m. Direction of applied force is,…

Q: Is the net torque changed when a partner on a seesaw stands or hangs from her end instead of…

A: No, if one simply hangs or stands, the force on the lever arm does not change. As, torque stands for…

Q: Calculate the torque of a door upon applying 5 N of force to open it and has a lever arm of 2.3 m?

A: Given, Force = 5N Lever arm = 2.3 m The lever arm is the perpendicular distance from the axis of…

Q: If a car can generate 230lbs/ft of torque at the wheels, and the rear tires are 18inches in…

A: Let f denotes the force on each of the rear tires, τ denotes the torque on each of the rear tires,…

Q: A light rod is being used as a lever as shown. The fulcrum is 1.20 m from the load and 2.40 m from…

A: Given: The mass of the load is 16.9 kg. The free-body diagram is given below.

Q: calculate the torque product by a 50 N perpendicular force at the end of a 0.2 m long wrench

Q: A weight of 30 N is located a distance of 10 cm from the fulcrum of a balance beam. At what distance…

Q: Suppose there is a 20 m stick that is pivoting about its center of mass at 10 m. On the right side…

A: length of stick = 20 m pivot point = midpoint of the stick = 10 m first weight (w) = 10 N position…

Q: The crank arm of bicycle pedal is 16.5 cm. If a 52kg woman puts all her weight on the pedal, how…

Q: What is the torque required to accelerate a rotating object if it starts rotating at 10 degrees per…

Q: A force of magnitude 30 lbs acts on the end of a wrench as shown. The wrench is 8 inches long and…

A: Given Force=30 lbs =133.5 N Length of wrench=8 in=0.2032 m

Q: A bar 2.0 meters long makes an angle of 30° with the horizontal. A vertical force of 40 N is applied…

A: Given: The length of the bar is 2.0 m. The angle is 30 degrees. The force applied is 40 N. The…

Q: Aplank resting on a pivot has a child on each end. The plank balances for any two children because…

A: we have the following diagram

Q: If my cat pulls a rope attached to the wall with 100N, and it is .5m long, and .3kg, what torque…

Q: You hold a meterstick horizontally with the same mass suspended at the end. Rank the torque needed…

A: Torque = force x lever arm In all three cases, the mass is same so gravitational force is also same.

Q: A load of 10 kg is placed in a lever system 0.75 m from the fulcrum as shown in the figure below.…

Q: A rusted bolt requires 30J of torque to be loosened. If only 40N of force is applied to a wrench…

Q: Betermine the net torque (about point P at one end) of the 4.0-m-long uniform beam shown in the…

A: Let, counterclockwise torque is positive. Net torque is given by, net = 1 + 2 - 3 net = F1*sinA1*r1…

Q: Which of these has maximum torque? The angle between the applied force and moment arm is 30 degrees…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: The lug nuts on a car wheel require tightening to a torque of 90 N.m. If a 30 cm long wrench is…

A: Required Torque= 90 N.m Length of wrench= 0.3 m

Q: To loosen a bolt, an electrical engineer can exert 700N of force on the M12 Driver. What amount more…

Q: The gardening tool shown in the photo attached is used to pull weeds. If a 1.23 N.m torque is…

A: Consider the torque acting on the system,

Q: A man is holding an 8.00-kg vacuum cleaner at arm's length, a distance of 0.550 m from his shoulder.…

A: Given data The mass of the vacuum cleaner is m = 8 kg The length of the arm is d = 0.550 m The…

Q: To tighten a spark plug, it is recommended that a torque of 15 N·m be applied. If amechanic tightens…

A: The equation for the magnitude of the torque is given by,

Q: What is Torque as a Vector?

Question

What is the torque produced when a force of 15N is applied to open the door that is 2.5 meters wide? Note that the point of application of the force is in the middle of the door .

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

The cylindrical head bolts on a car are to be tightened with a torque of 62.0Nm . If a mechanic uses a wrench of length 20 cm, what perpendicular force must he exert on the end of the wrench to tighten a bolt correctly?
Two flywheel fo negligible mass and different radii are bounded together and rotate about common axis (see below). The smaller flywheel of radius 30 cm has a cord that has a pulling force of 50 N on it. What pulling force needs to be applied to the cord connecting the larger flywheel of radius 50 cm such that the combination does not rotate?
Can a single force produce a zero torque?
What force must be applied to end of a rod along the x-axis of length 2.0 m in order to produce a torque on the rod about the origin of 8.0k Nm ?
Can a set of forces have a net force that is zero and a net torque that is not zero?
An automobile engine can produce 200Nm of torque. Calculate the angular acceleration produced if 95.0 of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0-kg disk that has a 0.180-m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
Can a set of forces have a net torque that is zero and a net force that is not zero?
A force of F=(2.00i+3.00j) N is applied to an object that is pivoted about a fixed axle aligned along the z coordinate axis. The force is applied at the point r=(4.00i+5.00j)m. Find (a) the magnitude of the net torque about the z axis and (b) the direction of the torque vector .
What is the torque abot the origin of the force if it is applied at the point whose position is:
A constant torque is applied to a rigid body whose moment of inertia is 4.0kgm2 around the axis of rotation. If the wheel starts from rest and attains an angular velocity of 20.0 rad/s in 10.0 s, what is the applied torque?
Give an example in which a small force exerts a large torque. Give another example in which a large force exerts a small torque.
A horizontal beam of length 3 m and mass 2.0 kg has a mass of 1.0 kg and width 0.2 m sitting at the end of the beam (see the following figure). What is the torque of the system about the support at the wall?