SOLVE steps by stepsusing ASD methodWhat size of threaded rod is required for member AB given in figure below. The applied load ofX2=474 kN is the live load and neglect the weight of the member BC. What size of threaded rod is required for member AB given in figure below. The applied load ofX2 is the live load and neglect the weight of the member BC.X2 kN4.5 m2.7 m

Inclination of threaded rod is given astanθ=2.74.5θ=30.96° Now from the FBD of beam There are two…

Answered: What size of threaded rod is required…

What size of threaded rod is required for member AB given in figure below. The applied load of X2 is the live load and neglect the weight of the member BC. X2 kN Y 4.5 m 2.7 m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.9.4P

See similar textbooks

Related questions

Q: A tied column 300 x 350 mm as shown in the figure is reinforced with 6 pieces steel bars having fy =…

A: Answer : We are given b = 300 mm h = 350 mm f'c = 21 Mpa fy = 414 Mpa Factored load Pu = 1200 KN…

Q: Determine the magnitude and location of the resultant for the distributed load system shown with…

Q: For the simply supported beam shown below, determine the internal resultant loadings at a point 0.5…

Q: Q1: Draw the internal loading diagrams (N, Ty, Mx). State the extremum values on the diagı 2 kN/m A…

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

A: Deflection will be determined by the first mentioned method i.e. double integration.For other…

Q: Construct the shear-force diagram and identify the largest negative shear force. Assume a = 6.0 ft,…

A: Given:- a = 6.0 ft b = 12.0 ft c = 24.0 ft P = 2700 lb W = 1150 lb/ft To find:- Shear force…

Q: A cantilever beam carries a varying load as shown in the figure. If E = 200,000 Mpa and I=120×10^6…

Q: Question 3 An 8 m long beam is supported by a column at each end and has a dead load of 3 kN/m, and…

A: Solution: Given: DL = 3 kN/m LL = 1000 kg = 9.81 kN Span = 8 m

Q: Po,PL 5 ft 14" Figure 1: Concentrated dead load Pp cantilever beam (ignore the self-weight). 20 kips…

A: The given data is shown below:

Q: A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly…

Q: For the beam shown, calculate the magnitude of the bending stress (in psi) at the bottom of the beam…

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

A: As per company's guidelines we can only answer first question. Kindly post other questions as…

Q: Find the maximum uniformly distributed load (w) the beam can carry if the allowable bending and…

A: It is required to find the maximum safe udl the beam can carry. It will be minimum from the two…

Q: Find the critical buckling load (SI unit) for a long column with a length of 3 m and a fixed -…

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

A: Deflection will be determined by the first mentioned method i.e. double integration.For other…

Q: Q.2 A 6.0 m cantilever steel beam ABC sustains a point load of 150 kN at free end C and a uniformly…

A: Considering a section X-X at distance x from points B and C. Span BC (0-3): MX-X=-150x Span AB…

Q: Refer to the previous problem. Determine the balanced load in kN. O1355 < 1553 1535 5135 Previous…

Q: (a) In terms of w, M,, and L, determine the load vectors (b) In terms of E, I, and L, determine the…

A: Draw free body diagram Draw determinate structure and do numbering Draw determinate structure with…

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

Q: Construct the shear-force diagram and identify the largest negative shear force. Assume a = 3.7 ft,…

Q: A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly…

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

A: Deflection will be determined by the first mentioned method i.e. double integration.For other…

Q: A 10 m B

Q: L For the beam shown above with length L= 7 m with the applied uniformly distributed load of w = 17…

Q: 5. The beam shown is resting on two moveable supports. It carries a uniform love load of 140 N/m and…

Q: The beam AB supports two concentrated loads and rests on soil that exerts a linearly distributed…

Q: A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly…

Q: A simple beam is loaded with a dead load, live load and axial load as shown in the Figure below.…

A: Given beam is simply supported beam and the data is: Ultimate Bending moment=400 Kn-m Ultimate shear…

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

Q: saw-tooth loading is applied as shown in the figure. The flexural tiffness (EI) of the beam is 1×10³…

A: Given- A propped cantilever beam carrying UVL loading. Required- To calculate support Reactions of a…

Q: For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 0.61 in from…

Q: For the simply supported beam shown below, determine the internal resultant loadings at a point 0.5…

Q: A reinforced concrete girder having a simple span of 8 m carries a uniform service dead load of 20…

A: Uniform service dead load= 20 kN/m Uniform service live load= 36 kN/m Width of beam=450 mm Depth of…

Q: Find the maximum uniformly distributed load (w) the beam can carry if the allowable bending and…

Q: LOmPa aGMPa 30 MPa

A: Solution Given Data σx=30 MPaσy=10 MPaζxy=26 MPa

Q: Completely solve and box the final answer. Illustrate the problem. Write legibly 2. A cantilever…

A: Given data in question Span member length UDL Point load Flexural stress Shearing stress To find…

Q: Current Attempt in Progress Construct the shear-force diagram and identify the largest negative…

Q: The continuous beam shown in the follow figure has a constant cross-section and supports a uniformly…

Q: Determine the magnitude and location of the resultant for the distributed load system shown with…

Q: :Determine the value of P, if the load W- 800 N.

Q: Find: 1. The magnitude of the 150N load is, 2. The direction of the 150N load is LB. a. NOTE: i. Use…

A: Consider the figure,

Q: A short post carries a downward load P = 133 kN as shown in the figure. Due to its eccentricity from…

Q: PROBLEM 1 Determine the value of load P if: (neglect friction) Block A = 8N Block B = 4N O = 45° P B…

Q: A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly…

Q: Find the maximum uniformly distributed load (w) the beam can carry if the allowable bending and…

Q: A 5-m long simply supported timber beam carries a uniformly distributed load of (12k N/m), as shown…

Q: Don't stress. Do your best. Forget the rest Question 2 5 pts A simply supported beam with P1=50 kN,…

Q: Find the maximum uniformly distributed load (w) the beam can carry if the allowable bending and…

A: Allowable bending stress = 60 MPa Allowable shear stress = 36 MPa

Q: QUESTION 1 A continuous beam ABCD having a uniformly distributed load of 15 kN/m on span BC and…

Q: For the given frame ABC in the figure below, if the 25KN/m uniform load is changed to 76KN/m and the…

A: Draw the free body diagram.

Question

SOLVE steps by steps

using ASD method

What size of threaded rod is required for member AB given in figure below. The applied load of
X2=474 kN is the live load and neglect the weight of the member BC.

What size of threaded rod is required for member AB given in figure below. The applied load of
X2 is the live load and neglect the weight of the member BC.
X2 kN
4.5 m
2.7 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

SOLVE steps by steps What size of threaded rod is required for member AB given in figure below. The applied load ofX2=474 kN is the live load and neglect the weight of the member BC.
Draw the Normal Force (N), Shear Force (T) and Bending Moment (M) diagrams of the beam whose loading condition is given in the figure. H=3ton , M=16tm, q1= 15t/m ,q2= 8t/m ,P=10ton ,a=8meter
2. A square aluminum bar is to support a load of 65kN on a length of 4.50 m. Assume pinned ends, Determine the length of each side E-70 GPa.
The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.35 in2. Find the vertical displacement (in inches and absolute value) of point Ccaused by the 2684-lb load if x = 9.9 ft and θ = 49.3ᵒ. Use E = 29213 ksi for steel. Note: Round off the final answer to four decimal places.
Situation 17. A w12x79 of A573 Grade 60 (Fy-415MPa) steel is used as a compression member. It is 8m long pinned at the top fixed at bottom with additional lateral support at mid height in the weak direction. The properties are as follows Ag=14,500 sq.mm = 258.6x10^6 mm^4 Iy=84.375x10^6 mm^4 Calculate the critical slenderness ratio with buckling about strong axis. calculate the critical slenderness ration with buckling about weak axis. calculate the flexural buckling stress Fcr in MPA
A 16 inch square tied column cross- section with 8-#8 bars, three in each face to resist factored loads and moments of Pu = 250 kips and Mux = 55 kip-ft, and Muy = 110 kip-ft. Use fy = 60 ksi and f’c = 4 ksi. What is the value of φPn in kips using Bresler Equation. Use two decimal places
The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.27 in2. Find the vertical displacement (in inches and absolute value) of point C caused by the 2448-lb load if x = 9.5 ft and θ = 41.7ᵒ. Use E = 29147 ksi for steel. Note: Round off the final answer to four decimal places.
Given a 2.2meter Wide Flange steel compression member with A=4851mm2, Ix=83069765mm4 and Iy=3563198mm4 with Fy = 345MPa. Calculate the design strength in KN if both ends are hinged or pinned. Express your answer in 2 decimal places.
For the beam loaded as shown, determine EIy midway between the supports.
pls answer I'll rate Use virtual work method and determine the following unknowns on the truss system shown below. Use A = 500 mm2 and E = 200 GPa.a. Horizontal displacement of joint G due to the applied loads in mmb. Horizontal displacement of joint G considering that the top chord members experience 60 °C increase in temperature in mm. Use α = 10-6/°C
A 16 inch square tied column cross- section with 8-#8 bars, three in each face to resist factored loads and moments of Pu = 250 kips and Mux = 55 kip-ft, and Muy = 110 kip-ft. Use fy = 60 ksi and f’c = 4 ksi. Using interaction diagram, determine the value of ρg in three decimal places.
What size of threaded rod is required for member AB given in figure below. The applied load of X2 =199 KN is the live load and neglect the weight of the member BC.