What variable factors to be consider before operating any lathe operations? How you can set these factors?

Q: During plain turning mild steel by a tool of geometry 0°, 0°, 7°, 8°, 12°, 90°, 0 (mm) at so= 0.35…

A:

Q: . What is the manufacturing process of lathe bed? Which material will be suitable for the product?

A: manufacturing process is pattern making and molding   Lathe bed is made of high-grade cast iron…

Q: Where are the areas on the lathe that should be given most caution? Why

A: A lathe can be described as a machine that rotates a workpiece about an axis to perform various…

Q: Q1. What are parameters of cutting process? mention it with units.

A:

Q: Why proper selection of cutting speed is important in machining? What is the main advantage of a…

A: Given Machining To find Significance of cutting speed Advantage of turret lathe Advantage of band…

Q: lathe machine, the maximum torque transmitted by a shaft exceeds the mean torque by 11 %. A power of…

A: For solution refer below images.

Q: with neat sketch explain any three different types mandrels used in a lathe. Why is it used

A: A devices which is used to hold the job for machining on lathes is called Lathe mandrels .   Few…

Q: A turning operation uses a 2/64 in nose radius cutting tool on a free machining steel with a feed…

A: Write the given values using suitable variables. Here r signifies nose radius, f signifies feed in…

Q: With a neat sketch, explain the 4 types of Taper turning operations?

A: Four different types of Taper turning operations are : Here a tool having broad nose angle and…

Q: The surface finish specification in a turning job is 0.90 um. The work material is cast iron. The…

A:

Q: Calculate the time required to machine a workpiece 170 mm long, 60 mm diameter to 165 mm long 50 mm…

A: Given:L1=170 mmL2=165 mmD1=60 mmD2=50 mmN=440 rpmf=0.3 mm/revd=2 mmApproach and overtravel=5 mm

Q: 1.10A O50 mild steel bar is being turned at 1.70 revis on a multi-tool center lathe having nine…

A:

Q: Define the lathe machine?

A: The definition of the lathe machine is given as under.

Q: A single-point HSS tool with a 3/64 in nose radius is used in a shaping operation on a ductile steel…

A:

Q: Explain with neat line diagram the working principle of simple gear train that can be use in lathe…

A:

Q: Q1) Explain the four types of chips formation with sketches? What is tool life in Lathe?

A: 1. CONTINUOUS CHIP- As the name shows these types of chips have a continuous segment and produce…

Q: Why should the overhang distance of a lathe tool be minimized? What occurs if a lathe tool is set…

A:

Q: dentify the lathe operations in the below mentioned diagram and name and explain them.?

A: Grooving, turning, cutting, sanding, and other processes are common on the lathe. If someone wishes…

Q: Draw a sound conclusion based on how you familiarized the key components of the lathe machine.…

A: Lathe machine: The main objective of this machine is to remove the extra material by rotating the…

Q: Q1\ a) The operation of drilling is to be done with a 25.4 mm ( diameter) twist drill in a brass…

A:

Q: how would you make the champhers on a lathe?

A: Chamfer refer to the slope  cut at any right edge of a work piece for example holes, ends of the…

Q: 1- Define lath Process, why the tool should have Red Hardness Property? 2- What are the kinds of…

A: 1. The measurement of material hardness at a high temperature is referred to as "hot hardness…

Q: how many relative surfaces in the turning process? and what are they, sh nage.

A:

Q: A part to be turned in an engine lathe must have a surface finish of 1.6 μm. The part is made of a…

A: Proper tool Nose radiusing improves machinability to some extent though. It increase the tool life…

Q: During plain turning mild steel by a tool of geometry 0°, 0°, 7°, 8°, 12°, 90°, 0 (mm) at so= 0.35…

A: Given data: a2=0.625 mms0=0.35 mm/revϕ=90° Need to determine the value of ξ.

Q: 1.10A O50 mild steel bar is being tumed at 1.70 revis on a multi-tool center lathe having nine…

A:

Q: 1) What are the factors that affect the life of the cutting tool in the turning processes.

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: In a lathe machine, the maximum torque transmitted by a shaft exceeds the mean torque by 18 %. A…

A: Given, P=3 kW=3×103 WN=625 rpmTmax=1.18Tm

Q: 4) How does the coefficient of friction affect the relationship between the friction force and the…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: mm and 7.6 An orthogonal machining operation is performed on a mild steel part 5 mm wide. The tool…

A: Introduction: The cutting velocity in orthogonal cutting is perpendicular to the breadth of the…

Q: What is a tree lathe?

A: In this problem, it is asking about the tree lathe.

Q: In what units are feed rates measured for lathe operations?

A: Feed rate is the measurement of the spindle's travel distance per rotation. The feed rate is…

Q: The end of a large tubular workpart is to be faced on a NC vertical boring mill. The part has an…

A:

Q: How can hardened work pieces which cannot be machined with conventional cutting tools  be finished…

A: Conventional machining process: A machining process in which mechanical energy is used and direct…

Q: In which lathe operation enlarging the already drilled hole can be produced.

A: Boring is a process in which a drilled hole made enlarged. It uses a single-point cutting tool.

Q: On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The cutting…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.