What would be the maximum weight W of the block, shown in the

Q: which is given. What are the x and : coordinates of the bracket's mass cen- ter? (The angle 0 in the…

A: To Find :  The x and z coordinate of the bracket mass . Given :  The total number of hole is n=4 The…

Q: metacentric height, (b)

A: Answer-Option c)

Q: find controid of the area

A:

Q: 1Flnd the centroid

A: given:

Q: vertical position so'c calalate the rcte of H.T in the cwity per cunit depth. Im

A:

Q: Find (I,) for the shaded area.

A:

Q: Find the controid for the shaded area

A:

Q: Determine the capacity, in liters, of the punch bowl shown if R=250 mm.

A: The given volume can be generated by revolving the following area about the y axis.

Q: Q1. Find the centroid 200 mm 200 mm 400 mm

A: As per Bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: What is the specific volume if the mass of an object is 120 lbs and the volume is 1250 ft3.

A:

Q: 5 kN +

A: Given

Q: une at F = 5.5 kN (Figur

A: solution as follows

Q: Find the unit for H. Show all steps

A: Given, all the units of each parameter Substituting these values in the above equation,

Q: cickness of the m, while that c nasses at a dis

A:

Q: i) the force that must be applied to the small piston. ii) the distance that the small piston has to…

A:

Q: This side of the dam always has the higher water level O dam height O Downstream O Upstream O Top…

A:

Q: What would be the resultant force Fof the triangular distributed load and its location d measured…

A: Given:

Q: For the shape shown, calculating Q from the centroid to the top of the shape would yield the same…

A: The given statement is TRUE.

Q: F2 2 m 2 m - 2 m

A: The force is a first order tensor that requires not only direction but also magnitude. These forces…

Q: Determine the force in KN, due to water acting on one side of the parabolic gate. Round your answers…

A:

Q: 1 kN/m 1m

A: Shear force is an internal force in any material which is usually caused by any external force…

Q: The center of gravity of the plane wire figure is located at G. Determine the lengths a and b. G/ 40…

A:

Q: Auerage heau dtrero = 2 Nimm2 Determine Maximum d hear Stren Sar rectangulan dection

A: Given data : Average shear stress is ratio shear force upon cross sectional area  The value of…

Q: The maximum safe air pressure of a tire is typically written on the tire itself. The label on a tire…

A: According to given condition  The maximum pressure in the tyre is 35psi

Q: Locate the ctrdof the volume

A:

Q: For the box shown below, determine the value of x if the total area is 94 cm³.

A: Given data                  Area of cuboid = 94 cm2                  Length = 4…

Q: Determine the force in cored AB 30° A В 800 lb/ft -15 ft- -15 ft Your answer

A:

Q: Find the weight in Newtons of the steel ball if its diameter is 2 in. Use the density of steel as…

A:

Q: Determine the absolute weight and the weight relative to the rotating earth of a 103-kg man if he is…

A: To find: The absolute weight and relative weight relative to the rotating earth. Given: The mass of…

Q: The volume of the syringe’s reading read as 4cc when the weight (pressure) was 600 g. Determine the…

A: Initial Volume, V1=4 ccWeight for 4 cc volume, M1= 600gFinal Volume, V2=2.5 cc

Q: Convert 589 mm to m.

A: Given Data : Length (L)=589 mm

Q: Determine the vertical component of A.

A:

Q: Determine the volume,

A: Given: P= 6.9 MPa T=316oC m= 0.9 kg H2O TO determine:' Volume occupied

Q: Convert 14 mm to its equivalent in m

A: 1mm = 0.001 m

Q: Determine the dimensions of the riser

A: Given: Diameter of casting mold = 12 cm r=6 cm Length=h= 20 cm Solidification time of casting = 0.9…

Q: Determine the capacity, in liters, of the punch bowl shown if R = 250mm.

A: Given data: R=250 mm

Q: The weight of the body is 100 lb. Determine its mass.

A:

Q: What should the magnitude of P be so that the resultant is as small as possible? (Express your…

A:

Q: Question 1 3.5m Water 2.5m L Quarter circle shown is 3.2m long and is submerged in water. Determine…

A:

Q: aonless pulley. The mass of gravity is 9.8 m/s².

A: acceleration- 9.8m/s2

Q: Determine the absolute weight and the weight relative to the rotating earth of a 85-kg man if he is…

A: Given Data : Weight of man m = 85 kg  Latitude ϕ = 36o Now,  Absolute weight = m × g  Wabs = 85 ×…

Q: If diameter of the cylinder increases, the pressure of the cylinder given from pump would be less.…

A: Pressure: Pressure is defined as force Per unit area.

Q: lind the locakion of te resultant force F of the wakev be Sianqulau gate and tc on force P to hold…

A:

Q: 18 A pendulum used for testing the impact resistance of a car is shown. From the given inf the…

A:

Q: A body weighs 250 lb at the earth's surface. Determine c. The weight of the body on the moon's…

A: Given   weight of the body on the earth's surface = 250 lb…

Q: Based on the given drawing, determine the center of gravity of the surface analytically if R = 2m

A: Where R = 2 m TO FIND: Center of gravity

Q: Q1. Find the centroid

A:

Q: Determine absolute pressure of gas A in the bulb

A: Given data; h1=17 cm=0.17 mh2=2 cm=0.02 mh3=5 cm=0.05 mρHg= ρ=13.6 g/mlρHg=13600 kg/m3Patm=101325 Pa…

Q: Compite the IMAf of the engine lift shown in The second diagram

A: Given data: The distance from the fulcrum to effort is, Di=2 ft. The distance from the fulcrum to…

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.