When a R = 87.7 O resistor is connected across a 11.3 V battery, a current of 113.2 mA flows. What isthe internal resistance of the battery and Terminal voltage of the battery ?A(1)E(MF)Rexternal(vexternalRinternal(a) internal resistance of the battery(in 2) =(b) Terminal voltage of the battery in V =Battery R,R,R3RRsIn the above circuit, R1 = 102, R2 = 402, R3 = 300, R4 = 202, R5 = 602. The battery voltage is 12V.1. The equivalent resistance of the circuit is =Ω2. The source current is =A3. The voltage drop across R3 is =4.The voltage drop across R2 is =V5. The power dissipated across R1 is =W12V

Emf = 11.3 V R = 87.7 ohm current = 113.2 mA = 0.1132 A

When a R = 87.7 resistor is connected across a 11.3 V battery, a current of 113.2 mA flows. What is the internal resistance of the battery and Terminal voltage of the battery ? A (1) E(MF) Rexternal external Rinternall (a) internal resistance of the battery(in N ) = (b) Terminal voltage of the battery in V = Battery

When a R = 87.7 resistor is connected across a 11.3 V battery, a current of 113.2 mA flows. What is the internal resistance of the battery and Terminal voltage of the battery ? A (1) E(MF) Rexternal external Rinternall (a) internal resistance of the battery(in N ) = (b) Terminal voltage of the battery in V = Battery

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 25P: A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of...

See similar textbooks

Similar questions

A child's electronic toy is supplied by three 1.58-V alkaline cells having internal resistances of 0.0200 inseries with a 1.53-V carbon-zinc dry cell having a 0.100- internal resistance. The load resistance is 10.0 . (a) Draw a circuit diagram of the toy and itsbatteries, (b) What current flows? (c) How much power is supplied to the load? (d) What is the internal resistance of the dry cell if it goes bad, resulting in only 0.500 W being supplied to the load?
Power P0 = I0 V0 is delivered to a resistor of resistance R0. If the resistance is doubled (Rnew = 2R0) while the voltage is adjusted such that the current is constant, what are the ratios (a) Pnew/P0 and (b) Vnew/V0? If, instead, the resistance is held constant while Pnew = 2P0, what are the ratios (c) Vnew/V0, and (d) Inew/I0?
If the terminals of a battery with zero internal resistance are connected across two identical resistors in series, the total power delivered by the battery is 8.00 W. If the same battery is connected across the same resistors in parallel, what is the total power delivered by the battery? (a) 16.0 W (b) 32.0 W (c) 2.00 W (d) 4.00 W (e) none of those answers
Resistors are commonly rated at 18W,14W,12W ,1 W and 2 W for use in electrical circuits. If a current of1 = 2.00 A is accidentally passed through a R=1.00 resistor rated at 1 W, what would be the most probable outcome? Is there anything that can be done to prevent such an accident?
A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg • °C, assuming no heat escapes?
Figure P18.19 shows a Wheatstone bridge, a circuit used to precisely measure an unknown resistance R by varying Rvar until the ammeter reads zero current and the bridge is said to be balanced. If the bridge is balanced with Rvar = 9.00 , find (a) the value of the unknown resistance Rand (b) the current in the 1.00 resistor. (Hint: With the bridge balanced, the wire through the ammeter can effectively be removed from the circuit, leaving two pairs of resistors in parallel.) Figure Pl8.19
Consider the circuit below. The battery has an emf of = 30.00 V and an internal resistance of r = 1,00 . (a) Find the equivalent resistance of the circuit and the current out of the battery. (b) Find the current through each resistor, (c) Find die potential drop across each resistor, (d) Find the power dissipated by each resistor, (e) Find the total power supplied by the batteries.
Figure P18.19 shows a Wheatstone bridge, a circuit used to precisely measure an unknown resistance R by varying Rvar until the ammeter reads zero current and the bridge is said to be balanced. If the bridge is balanced with Rvar = 9.00 , find (a) the value of the unknown resistance Rand (b) the current in the 1.00 resistor. (Hint: With the bridge balanced, the wire through the ammeter can effectively be removed from the circuit, leaving two pairs of resistors in parallel.) Figure Pl8.19
Explain why R=R0(1 + a?T) for the temperature variation of the resistance R of an object is not as accurate as P=P0(1 + a?T) which gives the temperature variation of resistivity P.
Three 60.0-W, 120-V lightbulbs are connected across a 120-V power source, as shown in Figure P18.50. Find (a) the total power delivered to the three bulbs and (b) the potential difference across each. Assume the resistance of each bulb is constant (even though, in reality, the resistance increases markedly with current). Figure P18.50
When a R = 90.9 Ω resistor is connected across a 12 V battery, a current of 123.9 mA flows. What is the internal resistance of the battery and Terminal voltage of the battery ? (a) internal resistance of the battery(in Ω ) = (b) Terminal voltage of the battery in V =
When you connect an unknown resistor across the terminals of a 1.50 V AAA battery having negligible internal resistance, you measure a current of 19.0 mA flowing through it. If you now place the resistor across the terminals of a 11.2 VV car battery having no internal resistance, how much current will flow?