When calculating motors, why do we use the NEC table amperage instead of the nameplate amperage?

Q: Why is a starting resistor needed to bring a motor up to speed?

A: The motor not turns on instantly when you connect supply across because it provide a very small…

Q: Differentiate between the Manual over Magnetic DC Motor Controller

A:

Q: 30. Excluding slip, at what speed (r/min) with a four-pole, 60 Hz, 240 Volt motor runs?

A:

Q: What will happen if we run the motor at nominal load without starting? Please observe and explain…

A:

Q: what is the laddered circuit of forward-reversed motor control?

A: Ladder diagrams are schematics used to describe industrial control logical systems. Since they…

Q: lue increase as the torque value increases?

A: An asynchronous motor is also known as an induction motor. A three-phase balanced supply is provided…

Q: A) Explain in details main used methods of electric braking of the DC shunt motor; draw the…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: What is a Vertical Speed Indicator?  -Operation -Parts

A: Vertical Speed Indicator      "flight instrument that indicates the rate of climb or descent or the…

Q: For what purpose was the asynchronous motor idle test performed? Please explain.

A: Need to find For what purpose was the asynchronous motor idle test performed?

Q: 16. What voltage may be applied to 230/460- volt motor if used with a part winding? Why?

A: What voltage may be applied to 230/460V motor if used with s part winding? Why?

Q: For the Starting Up the Power Station Simulator Why are certain operations blocked by isolators

A:

Q: How can you reduce the amount of voltage applied to the motor during inching?

A:

Q: 5. Explain the used of Drum Switches? Draw the 6 point , 8 point and 9 point drum switches? 6. How…

A: Since you have asked multiple questions, we will solve the one question for you. If you want any…

Q: In Induction motor, the load test has done. The result get is like the table below. 1) Explain why…

A: An induction motor is a commonly used AC electric motor in which the electric current necessary to…

Q: What  is plugging type braking?

A: Braking is of two type, one is for mechanical system and other is for electrical system. Hence,…

Q: What is the work of the Automatic transmission control system?

A:

Q: How can you determine the current that a direct current motor will draw at start-up

A: Above question is based on DC motor, the major classification of DC motor are Series motor Shunt…

Q: 2. Explain the effect of increasing the armature voltage on the behavior of the series wound machine…

A:

Q: What is the common speed for jet pump motors?

A: A motors of very speed are needed because the jet pump is needed to pump the water with very high…

Q: (Im) Does the excitation circuit current change as the motor current changes? explain the reasons.…

A: The excitation current does not change as the current motor changes because, in the shunt DC motor,…

Q: Why do we connect stop pushbuttons in series in a two - station motor control?

A: Control circuit of two station motor control is as,

Q: Name the three drive configurations that a gear set can transfer torque?

A:

Q: Why starters are used for DC motors. * Your answer

A: Starter is a device which is used to start DC motors.

Q: What happened to the dc if it runs without any starter?

A: What happened to the dc if it runs without any starter?

Q: For what purpose is the short circuit test performed in asynchronous motor? Please explain.

A: Need to explain about short circuit test in asynchronous motor

Q: Explain the effect of increasing the armature voltage on the behavior of the shunt wound machine…

A:

Q: What is starter ? Function of starter?

A: A motor starters main job is to start and stop the motor to which it is attached. These…

Q: Explain No load test or rotational loss test and Blocked rotor test.

A: Induction motor working Principle When an ac supply is connected to a stator it creates a rotating…

Q: Overload protection for motors is achieved by connecting _________. Explain how possible.

A: Need to explain overload protection for motors is achieved by connecting

Q: If the speed of the driving motor falls due to loading what will be the effects?

A: A motor is a device which convert electrical energy into mechanical energy.The speed (RPM)of a motor…

Q: Why the dc shunt motor running at the infinity speed?

A: In this question , we will write about how dc shunt motor running at infinite speed..

Q: Write a ladder program for two-motor control program, so that when the ignition switch is closed,…

A:

Q: Explain the differences between the stepper motor, servo motor and DC motor? Explain their…

A:

Q: explain open loop control system and closed loop control system

A: Open loop control system : A system in which there no influence of output on the input of system is…

Q: Where is the best place to look to find specific information about a motor, such as horsepower,…

A: The explanation is as follows.

Q: List 3 hazards when constructing (working) with a homemade D.C motor and how it can be managed?

A: List of some hazards when constructing (working) with a homemade D.C motor: Do not use in a…

Q: How can the current that a direct current motor will consume at start-up be determined?

A: Above question is based on DC motor, the major classification of DC motor are Series motor Shunt…

Q: What motor classification are generally found in use in high requirements like power drives for…

A: The three phase motor are generally found for high power requirements like power drives for…

Q: our Answers may be presented through Discussions, Drawings/Figures/Diagrams, Reference to NEC/PEC…

A: Given data, The conductor is connected to the three motors. Motor 1=50 hp Motor 2 = 40hp Motor 3 =…

Q: What is the purpose of the split-ring commutator in an electric motor that operates on DC power?

A: The electric device that uses electrical power input and the rotor stator set, to convert the…

Q: How much change in the energy of wind will take place if wind velocity becomes 5 times ? Change in…

A: Q.1) It is given that the change in the wind velocity is 5 times.

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.