When caluating the average power delivered to a load by an AC signed, it is not as straight forward a DC. It depence on the difference in phase between the einuecidal voltage across and currentthrough the load, and it related to their RMB values. The average power, or sometimes referred to as the active or real power, is stated to the underpinning sinusoidal vorage and current byP-VCo-WitteIn this question there is only a resistive load, R-8.60 and the ampitude is 98V.Decemmine the amplitude of the current through the foed 1-[Warkout the P50HzV196Vresistor, 6.80imR16.80tResetRUN/StopElectric PotentialPowerChargeSimulation SpeedCharge FlowCurrent Circuit:

Given data, From the given waveform maximum voltage Vm=96 V. Resistance R=6.8 Ω.

When causing the average power delivered to a load by an AC elgred, it is not as straight forward as DC. It depence on the difference in phase between the sincecidal voltage across and current through the load, and it related to their RMS values. The average power or somebmas referred to as the active or real power, is related to the underpinning srusoidal vorage and current by P-Vu le Cosy- We In this question there is only a resistive load, R-8.00) and the amplitude is 98V. Decemmine the amplitude of the current through the load I-L Workout the P DAV 50Hz R1 6.80 Reset RUN/Stop Electric Potential Power Charge Simulation Speed Charge Flow <

When causing the average power delivered to a load by an AC elgred, it is not as straight forward as DC. It depence on the difference in phase between the sincecidal voltage across and current through the load, and it related to their RMS values. The average power or somebmas referred to as the active or real power, is related to the underpinning srusoidal vorage and current by P-Vu le Cosy- We In this question there is only a resistive load, R-8.00) and the amplitude is 98V. Decemmine the amplitude of the current through the load I-L Workout the P DAV 50Hz R1 6.80 Reset RUN/Stop Electric Potential Power Charge Simulation Speed Charge Flow <

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

Give 5 problems and answers of ac circuits using super position theorem
For maximum average power transfer in the circuit shown in the figure, set the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
Derive the expression for the average and rms load voltage for a three phase HWCR operating with an RL type load. ? What will be the average power in the load for the circuit shown, when alpha = π/4 Assume SCR to be ideal. Supply voltage is 330 sin 314t. Also calculate the RMS power .?
Derive the power angle equation for a power system network and draw the corresponding curve.
What are ‘load curves’ and ‘load duration curves’? Discuss their utility in the economics of generation.
an overhead line is connected to a terminal apparatus through a length of single phase cable, the characteristics impedances being 400 and 50 ohms respectively. A traveling wave of vertical fromt and infinite tail of 100kv magnitudes originates in the overhead line and travels towards the junction with the cable during a period of 2us after the arrival of the wave at the junction. what voltage is reflected back into the line?
In the circuit given on the side Ra=Rb=Rc=Basic frequency of 13 Ohm loadsit is powered by an AC voltage of f= 60 Hz. Power derived from the sourceits value was measured as Pk=9372.12 Watts. Each switchingthe element is triggered in such a way that it will be at 180 degrees.The DC bus voltage (E=?) and the effective value of the ic phase current(ic rms=?) calculate.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Describe the concept of load flow analysis in power systems. How is it used to determine the steady-state operating conditions of a network?
Residential AC voltage for many European countries is 230 VRMS at 50 Hz. Calculate the following quantities for the AC signal: peak voltage, VP (in V); peak-to-peak voltage, VPP (in V); and period, T (in ms).
what is the mutual inductance in ohms (or the mutual inductive reactance ) between the two mutually-coupled inductors? if circuit to the left of load Z is converted into its Thevenin's equivalent, what would be the magnitude of ZTh in ohms? what is the phase angle of ZTh in degrees? what would be the phase angle of VTh in degrees? what would be the magnitude of VTh in volts if E = 120 V?
Find the rms value of the signal shown