Which choice is a feature of the SPI bus? O A formal specification with fixed bit rates O It uses open drain outputs O Data transmission is full duplex O Address and data are transmitted together

Q: Which of the following is not one of the bus signal groups? a. Control b. Address C. Data…

A: • A bus is a series of wires, rules, and protocol that allows data to be transferred.• Fetch is not…

Q: Which one of the following is not a valid line of the control bus? ) MRDC - memory read control MWTC…

A: Here, There are many control lines or signals in the control bus.

Q: Which of the following is not one of the bus signal groups? a. Control b. Address C. Data d.…

A: A bus is a set of wires, rules and protocol needed for transferring the data.

Q: The addressable mit in memory must equal the width of the bus. Select one: O True O False

A: Definition: Addressable Unit: In this the word endianness will be used for referring the sub…

Q: Buses use either synchronous timing or asynchronous timing. With synchronous timing, the occurrence…

A: Busesuse either synchronous timing or asynchronous timing.With synchronous timing, the occurrence…

Q: If an address bus needs to able to address eight devices, how many conductors will be required? What…

A: 1. Three conductors will be needed. Consider three conductors as three bits. with three bits eight…

Q: The following two transfers are allowed at the same time in the bus system of basic computer: O A.…

A: To find which two registers are allowed at the same time in the bus system of basic computer .

Q: Q2/ A- Sum of series of 10 numbers stored at memory location 0100H:0500H and then store result in…

A: Note - answering  first question according to our guidelines     Algorithm – Move 00 to register…

Q: O/M* = 0 for an I/O write bus operation.  True  False

A: Step 1:-   Introduction:-   IO/M' this is a pin which is used in 8085 microprocessor. In 8085…

Q: To designate the source or destination of the data on the data bus we use. Select one: O a. address…

A: 6. Explanation: Address lines are used to designate the source or destination of the data on the…

Q: *.which of the following is control bus signal. select all apply READ WRITE RESET none of the…

A: According  to the question control bus contains the control line for write data and the control line…

Q: Q2/ A- Sum of series of 10 numbers stored at memory location 0100H:0500H and then store result in…

A: Move 00 to register B immediately for carry Load the data of memory [0500] into H immediately Move…

Q: ina computer with a 32-bit data-bus, how many 4-bit wide memory components are used? the answer to…

A:

Q: 5) When using PIC32MZ EBI without an external address decoder (and note that anything that performs…

A: The  Externаl  Bus  Interfасe  (EBI)  mоdule  рrоvides  а  соnvenient,  high-sрeed  wаy  tо…

Q: Q3/ a- Write a program to interface the devices as input port A, output port B, input lower port C,…

A:

Q: Q3/ a- Write a program to interface the devices as input port A, output port B, input lower port C,…

A: GIVEN--- ADDRESS OF PORTS Start's From 430H TO SHOW---- A PROGRAM TO INTERFACE DEVICES as input Port…

Q: Choose... 1.default mode The real mode of operation is 2.is a control bus the protected mode of…

A: The solution to the given problem is below.

Q: Q2) What is the addressing mode of each of the following instructi a- INR C b- MVI M,00 c- RAL d-…

A: NOTE: Based on our rules, when multi-part questions are posted, we should answer only the first…

Q: Which of the following is true? I. According to the 80/20 rule, 80% of instructions are implemented…

A: 1. according to 80/20 , 80% of instructions are implemented and 20% are created     this statement…

Q: __________ is the process whereby devices connected to a bus autonomously determine which of the…

A: Distributed arbitration using self selection isthe process whereby device connected to a bus…

Q: e. How many address pins SRAM? are needed to address 64K

A: According to the guideline we are allowed to answer only the first question.   The question :: What…

Q: The flag bits in an ALU is defined as Lütfen birini seçin: O a. The status bit conditions b. The…

A: In processing, an ALU (Arithmetic Logic Unit) is a digital electronic circuit which conducts…

Q: Select one: O a.i do not know the answer b. Only PORTA & PORTE has a direction register associated…

A: The given statements are about digital electronic circuits:    The PIC microcontroller PIC16f877a…

Q: many conductors will be necessary if an address bus has to address eight devices? What if each of…

A: Given   How many conductors will be necessary if an address bus has to address eight devices? What…

Q: What are the sizes of the PC and IR registers? PC: 32 bits, IR: 28 bits O The size of both the PC…

A: We are asked the size of PC and IR. PC is Program counter and IR is instruction register. I have…

Q: The Intel 8255 processor with an 8-bit data bus is configured as shown in the figure below ( PORT_A…

A: Solution:--   1)The given question is an type of the multiple choice question as it has been defined…

Q: The Intel 8255 processor with an 8-bit data bus is configured as shown in the figure below ( PORT_A…

A: Solution:--       1)The given question is an type of the multiple choice question as it has been…

Q: 3-)It is possible to establish a BUS structure with RS232 communication. True False

A: Here is the Answer and Explanation

Q: To use instruction OUT DX, AL to send data information to an output port, which register must be…

A: Answer: The correct option is (b) => DX register holds the 16-bits Port address information

Q: questions. One bus cycle 57 St S4 S7 CLK ADi-Aaa AS LDS UDS BAW DTACK from memory Chata memony…

A: Timing diagram of read cycle is given and after observing the diagram answers are given below

Q: Calculate the values of the pins A0 and BHE’ and how many bus cycles are required for completing the…

A: Answer: I have given answered in the handwritten format in brief explanation.

Q: Assume you want to use Timer 1 to generate a mode 6 (9 bit Fast mode PWM) signal. What is the…

A: Question :- what is the highest frequency you can produce given cpu clock is 8 MHZ Answer :- 60 Hz

Q: 1.default mode The real mode of operation is 2.is a control bus the protected mode of operation is…

A: Solution:

Q: Which type of I/O has the disadvantage that all I/O data transfers must take place through the AL…

A: Type of I/O has the disadvantage that all I/O data transfers must take place through the AL or AX…

Q: In a Mil-Std 1553 Bus, one of the Remote Terminals (Terminal Address 4) would like to send the…

A: The answer is

Q: What is the frequency for a bus that has a width of 64 bits and bandwidth of 125 MBps as specified…

A: First of all, let's understand what is Bus Topology.   A bus topology is a topology for a Local Area…

Q: What is the frequency for a bus that has a width of 64 bits and bandwidth of 125 MBps as specified…

A: In order to calculate the bandwidth of a system's data bus, following formula is being considered:…

Q: The text talks about bus protocol. What is Protocol? Why does the bus require a protocol?

A: What is protocol: it is a set of rules to determine how data is transmitted and received between…

Q: Question 4 How do you think the TS and NT flag bits differ from each other? Question 5 Explain…

A: 4. TS Flag bits: Task Switch flag if set, indicates the next instruction using extension will…

Q: In _______ transmission, a start bit and a stop bit frame a character byte. a. asynchronous serial…

A: Here in this question we have asked about the transmission in which a start bit and stop bit frame a…

Q: Q3) A-Write an assembly program to duplicate (x2) ten memory contents located at starting address…

A: NOTE Below is the answer for the given question. Hope you understand it well. If you have any…

Q: Question 1 What is meant by "Full Duplex" when referring to a serial interface?

A: Given: When it comes to serial interfaces, what does full duplex mean?

Q: Question 1 What is meant by "Full Duplex" when referring to a serial interface?

A: Actually, given question regarding full duplex serial communication.

Q: Question 1 What is meant by "Full Duplex" when referring to a serial interface?

A: Given: When it comes to serial interfaces, what does full duplex mean?

Q: TRUE or FALSE? A bus is a collection of wires that carry information as electrical signals between…

A: Actually, bus is used to transfer the information from source to destination.

Q: TRUE or FALSE? A bus is a collection of wires that carry information as electrical signals between…

A: A bus is collection of wires that carry information as electrical signals between hardware…

Q: Which of the following is true? I. According to the 80/20 rule, 80% of instructions are implemented…

A: To be determine: Select the right option

Q: Write MIPS code to echo one keyboard input to the monitor, where your code shall do the following:…

A: the program is given below:-

Q: What is a major reason for "signal multiplexing" or "pin multiplexing" in a microcontroller?…

A: The major reason for signal multiplexing or pin multiplexing in a microcontroller is    It Allow the…

Q: What is a major reason for "signal multiplexing" or "pin multiplexing" in a microcontroller?…

A: Allow the microcontroller to contain more functionality than if peripheral assignments to pins were…