Which material is the best for thermal conductor but also an effective insulator to attach the elctronic circuitry to a subtrate material. With the consideration that due to the heat generated by other components, the substrate material has a working environment of 800 - 1000 K.In your opinion which material is the best to substrate?Provide three materials and its comparison.

Which material is the best for thermal conductor but also an effective insulator to attach the elctronic circuitry to a subtrate material. With the consideration that due to the heat generated by other components, the substrate material has a working environment of 800 - 1000 K.In your opinion which material is the best to substrate?Provide three materials and its comparison.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.33P

See similar textbooks

Similar questions

Explain FIVE (5) justification with examples for coating an engineeringcomponent with ceramics(b) In a certain welding operation, the system can produce welding heat capable oftransferring 2.7 kW to the surface of a metal part. It is observed that the heated areais circular. It is further observed that the heat intensity decreases with increasingradius in which 50% of the power is transferred within a circle of diameter 2.54mm while 75 % is transferred within a concentric circle of diameter of 6.35 mm. (i) Determine the power densities in the 2.54 mm diameter inner circle.(ii) Determine the power densities in the 6.35 mm diameter ring that lies around the inner circle.(iii) Analyze the power densities in Q5b (i & ii) for sufficiency in melting themetal.
If temperature difference is doubled whereas thermal conductivity and wall thickness are halved, what will be change in heat conducted through wall?
Solve this with diagram: An engine cover is made from 1 cm thick stainless steel plate (k = 14 W/m K). Air on the inside of the engine cover is heated to 340°C with a heat transfer coefficient of 7 W/m2K. Outside of the engine coverthe ambient air has a temperature of 70°C. If oil was spilled on the outside of the engine cover (ambient side), it could ignite if the surface temperature were to exceed 200°C. In this configuration, would spilled oil ignite? Use calculations to justify your answer. If a 4 mm thermal coating (k = 1.1 W/m K) was applied tothe outside of the engine, what would the outside temperature of the engine cover be reduced to? Solve it with resistors method
Solve this with diagram: An engine cover is made from 1 cm thick stainless steel plate (k = 14 W/m K). Air on the inside of the engine cover is heated to 340°C with a heat transfer coefficient of 7 W/m2K. Outside of the engine coverthe ambient air has a temperature of 70°C. If oil was spilled on the outside of the engine cover (ambient side), it could ignite if the surface temperature were to exceed 200°C. In this configuration, would spilled oil ignite? Use calculations to justify your answer. If a 4 mm thermal coating (k = 1.1 W/m K) was applied tothe outside of the engine, what would the outside temperature of the engine cover be reduced to?
Although many pots and pans are made of stainless steel, the bottoms often have either a roll-bonded layer of pure copper (Cu) or a brazed or embedded disk of pure aluminum (Al). Use material property values to explain why this design approach leads to more uniform heat dispersal across the bottom of the pan (reducing ‘hot spots’ during cooking).
Determine the latent heat gain from the occupants for an office building with a floor area of 150m x 70m. Working time of 20 occupants is from 9am to 5pm with working-break. Assume a diversity factor of 75%
How does a thermal printer work, and what are some industries that commonly use thermal printing technology?
A composite wall is formed of a 2.5 cm copper plate, a 3.2 mm layer of asbestos,and a 5 cm layer of fiberglass. The wall is subjected to an overall temperaturedifference of 560oC. Calculate the heat flux through the composite structure.
Calculate the overall heat loss and the temperature profile for each interface if the length of the cylinder is 50 m.Please write your answers legibly.
Example 7.9: A one meter long metal rod is thermally insulated in its circumference. The terminal temperatures of the rod are measured to be 100C and 20C as illustrated in the figure below. Determine the heat fluxes in the rod. The rod is made of two different materials of copper and aluminum.
An industrial process to harden ball bearings involves quenching them in a cooling bath at40°C. The bearings move on a conveyor belt from an oven, through the cooling bath, andthen out to air dry. The oven is long enough that the bearings reach a uniform temperatureof 900°C before exiting the oven. The ball bearings must exit the cooling bath no hotterthan 100°C. The ball bearings are made of AISI 316 Stainless Steel and the convectioncoefficient between the bearings and the cooling fluid can be considered constant at ℎ =600 W m2-K⁄ . You can find thermophysical properties of different materials in Appendix Aof the Bergman textbook.a) What is the largest diameter ball bearing that can be treated as thermally lumpedfor this cooling process? Take ? at a reasonable average temperature for this process.You do not need to interpolate if the average temperature is within ~30 K of a giventable value.b) The cooling bath is 5 m long. Using the diameter you found in part (a), estimate thespeed…
Solve for this : An engine cover is made from 1 cm thick stainless steel plate (k = 14 W/m K). Air on the inside of the engine cover is heated to 340°C with a heat transfer coefficient of 7 W/m2K. Outside of the engine coverthe ambient air has a temperature of 70°C. If oil was spilled on the outside of the engine cover (ambient side), it could ignite if the surface temperature were to exceed 200°C. In this configuration, would spilled oil ignite? Use calculations to justify your answer. If a 4 mm thermal coating (k = 1.1 W/m K) was applied tothe outside of the engine, what would the outside temperature of the engine cover be reduced to?