Which of the following are characteristics of series circuits? Select all that apply. There are multiple paths for current to follow through the circuit. The voltage is divided among all devices in the circuit. □ If one device in the circuit stops allowing current to flow, all other devices in the circuit will also stop functioning. The voltage across each device must be the same. There is only one path for current to follow through the circuit. The same amount of current flows through all devices in the circuit.

Which of the following are characteristics of series circuits? Select all that apply. There are multiple paths for current to follow through the circuit. The voltage is divided among all devices in the circuit. □ If one device in the circuit stops allowing current to flow, all other devices in the circuit will also stop functioning. The voltage across each device must be the same. There is only one path for current to follow through the circuit. The same amount of current flows through all devices in the circuit.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter29: Direct Current (dc) Circuits

Section: Chapter Questions

Problem 28PQ: The emf devices in the circuits shown in Figure P29.28 are identical. a. Redraw circuit 1 in figure...

See similar textbooks

Similar questions

A 500- resistor, an uncharged 1.50-F capacitor and a 6.16-V emf are connected in series, (a) What is the initial current? (b) What is the RC time constant? (c) What is the current after one time constant? (d) What is the voltage on the capacitor after one time constant?
Integrated Concepts If you wish to take a picture of a bullet traveling at 500 m/s, then a very brief flash of light produced by an RC discharge through a flash tube can limit blurring. Assuming 1.00 mm of motion during one RC constant is acceptable, and given that the flash is driven by a 600F capacitor, what is the resistance in the flash tube?
An electronic apparatus may have large capacitors at high voltage in the power supply section, presenting a shock hazard even when the apparatus is switched off. A “bleeder resistor" is therefore placed across such a capacitor, as shown schematically in Figure 21.50, to bleed the charge from it after the apparatus is off. Why must the bleeder resistance be much greater than the effective resistance of the rest of the circuit? How does this affect the time constant for discharging the capacitor?
Consider the circuit shown in the preceding problem. Write equations for the power supplied by the voltage sources and the power dissipated by the resistors in terms
An automobile starter motor has an equivalent resistance of 0.0500 and is supplied by a 12.0-V battery with a 0.0100- internal resistance, (a) What is thecurrent to the motor? (b) What voltage is applied to it? (c) What power is supplied to the motor? (d) Repeat these calculations for when the battery connections are corroded and add 0.0900 to the circuit. (Significant problems are caused by even small amounts of unwanted resistance in low-voltage, high-current applications.)
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
The emf devices in the circuits shown in Figure P29.28 are identical. a. Redraw circuit 1 in figure P29.28, including (and labeling) the current in each branch of the circuit. Apply the junction rule to write an equation in terms of the currents you have labeled. b. Repeat part (a) for circuit 2 in Figure P29.28. c. Simplify your equations if necessary, and compare your answers for each circuit. What can you say about the two circuits?
A 2.00- and a 7.50F capacitor can be connected in series or parallel, as can a 25.0- and a 100k resistor.Calculate the four RC time constants possible from connecting the resulting capacitance and resistance in series.
Figure P29.60 shows a simple RC circuit with a 2.50-F capacitor, a 3.50-M resistor, a 9.00-V emf, and a switch. What are a. the charge on the capacitor, b. the current in the resistor, c. the rate at which the capacitor is storing energy, and d. the rate at which the battery is delivering energy exactly 7.50 s alter the switch is closed?
A 2.00- and a 7.50-F capacitor can be connected in series or parallel, as can a 25.0- and a 100k resistor. Calculate the four RC time constants possible from connecting the resulting capacitance and resistance in series.
A battery has an emf and internal resistance r. A variable load resistor R is connected across the terminals of the battery. (a) Determine the value of R such that the potential difference across the terminals is a maximum. (b) Determine the value of R so that the current in the circuit is a maximum. (c) Determine the value of R so that the power delivered to the load resistor is a maximum. Choosing the load resistance for maximum power transfer is a case of what is called impedance matching in general. Impedance matching is important in shifting gears on a bicycle, in connecting a loudspeaker to an audio amplifier, in connecting a battery charger to a bank of solar photoelectric cells, and in many other applications.
To get the minimum current, the connection should be in series. If you create a series connection with 30V DC source and three resistors with R1 = 50Ω, R2 = 75Ω, and R3 = 100Ω, how do you calculate for the total current (IT) and the current flowing in each resistor (I1, I2, I3), and the total voltage (VT) and the voltage across each resistor (V1, V2, V3)? How do you also determine the power dissipated by each resistor (P1, P2, P3) and by the whole circuit (PT)??