Which of the following is not a choice for placing a surface texture symbol on aview?OA) Center line of a cylinder.B) Visible line of the edge view.OC Extension line extended from the edge view.D) Shoulder of a leader line pointing to surface.A number under the horizontal bar on the right side of the check mark symbolpecifies theOA) roughness averageB) surface mismatchC) sampling lengthD) maximum peakVarious machining processes can be specified above the horizontal bar on the checkmark. Which of the following is not likely?A) Mill.B) Shine.C) GrindD) Lap.

Question
Asked Nov 18, 2019
1 views

I need answers to these 3 parts for a review activity.

Which of the following is not a choice for placing a surface texture symbol on a
view?
OA) Center line of a cylinder.
B) Visible line of the edge view.
OC Extension line extended from the edge view.
D) Shoulder of a leader line pointing to surface.
A number under the horizontal bar on the right side of the check mark symbol
pecifies the
OA) roughness average
B) surface mismatch
C) sampling length
D) maximum peak
Various machining processes can be specified above the horizontal bar on the check
mark. Which of the following is not likely?
A) Mill.
B) Shine.
C) Grind
D) Lap.
help_outline

Image Transcriptionclose

Which of the following is not a choice for placing a surface texture symbol on a view? OA) Center line of a cylinder. B) Visible line of the edge view. OC Extension line extended from the edge view. D) Shoulder of a leader line pointing to surface. A number under the horizontal bar on the right side of the check mark symbol pecifies the OA) roughness average B) surface mismatch C) sampling length D) maximum peak Various machining processes can be specified above the horizontal bar on the check mark. Which of the following is not likely? A) Mill. B) Shine. C) Grind D) Lap.

fullscreen
check_circle

Expert Answer

Step 1

Surface texture symbol placed on the surface or edge of the part feature either directly or using leader line. But do not place a symbol center line of cylinder or an axis.

Thus, the correct option is option (A) center line of cylinder.

Step 2

A number under the horizontal bar on the right side of the check mark symbol specifies the sampling length.

...

Want to see the full answer?

See Solution

Check out a sample Q&A here.

Want to see this answer and more?

Solutions are written by subject experts who are available 24/7. Questions are typically answered within 1 hour.*

See Solution
*Response times may vary by subject and question.
Tagged in

Engineering

Mechanical Engineering

Related Mechanical Engineering Q&A

Find answers to questions asked by student like you

Show more Q&A add
question_answer

Q: Please solve the question

A: Consider the T-S diagram of the system. Here the saturated steam enters at point 1 at pressure of 30...

question_answer

Q: Steam enters a counterflow heat exchanger operating at steady state at 0.07 MPa with a quality of 0....

A: Determine the specific enthalpy and temperature from property table of “Saturated water – Pressure t...

question_answer

Q: As shown in the figure, air with a volumetric flow rate of 14,000 ft3/min enters an air-handling uni...

A: Determine the specific volume. 

question_answer

Q: A 62-kg copper block initially at 140°C is dropped into an insulated tank that contains 90 L of wate...

A:  Refer the Table “Properties of common liquids, solids, and foods”, select the specific heat of copp...

question_answer

Q: Problems within the wall is T(x) = a(L- ) +b where a = 10°C/m2 and b 30°C, what is the thermal con- ...

A: Given data as per questionAssumptionsSteady state condition.One dimensional conductionNo internal he...

question_answer

Q: I need the answers to this question.

A: The explanation of the above terms have been explained below.

question_answer

Q: Problem 2: Water flows in a horizontal pipe with an I.D. of 10cm (circular cross-section) and a leng...

A: Given data as per question

question_answer

Q: I need answers for questions 1, 2, and 3, pertaining to the print provided.

A: Note:As we are entitled to answer only a single question. We’ll answer question no. 1 for you. Pleas...

question_answer

Q: it has been determined that chatter and brake pull are being caused by hard spots on the brake drum:...

A: The raised or projected surfaces of the brake drum due to braking heat is known as hard spots.