Which of the following is not an axisymmetric problem? (A) A thick-walled cylindrical pressure vessel under internal and external pressure (B) Flywheel (C) Rotating compound cylinder (D) A solid cylindrical rod under external pressure (E) A thick-walled cylindrical vessel subjected to internal pressure and bending

Which of the following is not an axisymmetric problem? (A) A thick-walled cylindrical pressure vessel under internal and external pressure (B) Flywheel (C) Rotating compound cylinder (D) A solid cylindrical rod under external pressure (E) A thick-walled cylindrical vessel subjected to internal pressure and bending

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.13P: : A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered...

See similar textbooks

Similar questions

: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.
A vertical shaft 20 mm in dia and 100 cm long is mounted in long bearings and carries a rotor of mass 10 kg midway between bearings. The center of rotor is 0.5 mm away from axis of shaft. Neglect the weight ofshaft and take E-200 GPa forshaft material. Determing whirling speed of shaft and bending stress induced in it when it is rotating at 2000 rpm.
ts=600g, TL=18pounds , angle=780degree ,can you please find the solution and free body diagram
A 15,000 N crane pivots around a friction-free axle at its base and is supported by a cable making a 25∘ angle with the crane (Figure 1). The crane is 16 m long and is not uniform, its center of gravity being 7.0 m from the axle as measured along the crane. The cable is attached 3.0 m from the upper end of the crane. 1. When the crane is raised to 55∘ above the horizontal holding an 11,000 N pallet of bricks by a 2.2 m very light cord, find the tension in the cable. 2. Find the horizontal component of the force that the axle exerts on the crane.
A tall open-topped standpipe has an inside diameter of 3020 mm and a wall thickness of 8.6 mm. The standpipe contains water, which has a mass density of 1,000 kg/m3.(a) What height h of water will produce a circumferential stress of 18.3 MPa in the wall of the standpipe?(b) What is the axial stress in the wall of the standpipe due to the water pressure?
A 14 cm x 18 cm air compressor has 6 bolts on cylinder head with yield stress of 450 MPa. If the bolt stress area is 0.14 in2, calculate the maximum pressure inside the cylinder.
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Calculate the maximum shear stress with Mohr's circle? d) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion?
With pressure steel tank axis α = 750manufactured as degree angle helical weldedreferences Tank radius r = 0.80 m. wall thickness is 15 mm The internal pressure of the Tank is p = 2.8 kPa. Elasticity modulus of steel used in manufacturing e = 200 GPa and position repair ν = 0.3 stop For the cylindrical part of the tank; a-) Find circular and longitudinal stresses. b-) Find the largest in-plane and out-plane shear stresses. c-)Find a circular and longitudinal shape change. d-)Find normal and shear stresses formed in the welding seam. These stressesshow on the properly rotated element.