The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.

The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.18P: A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed...

See similar textbooks

Similar questions

Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
Consider a uniform ladder of length 4.3 m and mass 10 kg. The ladder is falling over, pivoting about the end that is touching the ground. Someone is pushing on the top end of the ladder with a horizontal force of size 415 N. At the instant when the ladder makes a 46 degree angle with the horizontal, calculate the net torque on the ladder about its bottom end, in N m. Make your answer positive, and use g = 10 m/s2. (Please answer to the fourth decimal place - i.e 14.3225)
A vertical shaft 25 mm diameter and 0.75 m long is mounted in long bearings and carries a pulleyof mass 10 kg midway between the bearings. The centre of pulley is 0.5 mm from the axis of theshaft. Find (a) the whirling speed, and (b) the bending stress in the shaft, when it is rotating at 1700r.p.m. Neglect the mass of the shaft and E = 200 GN/m2.
A vertical shaft 20 mm in dia and 100 cm long is mounted in long bearings and carries a rotor of mass 10 kg midway between bearings. The center of rotor is 0.5 mm away from axis of shaft. Neglect the weight ofshaft and take E-200 GPa forshaft material. Determing whirling speed of shaft and bending stress induced in it when it is rotating at 2000 rpm.
nonuniform beam 4.50 m long and weighing 1.40 kNmakes an angle of 25.0° below the horizontal. It is held in position bya frictionless pivot at its upper right end and by a cable 3.00 m fartherdown the beam and perpendicular to it . The center ofgravity of the beam is 2.00 m down the beam from the pivot. Lightingequipment exerts a 5.00 kN downward force on the lower left end ofthe beam. Find the tension T in the cable and the horizontal and verticalcomponents of the force exerted on the beam by the pivot. Start bysketching a free-body diagram of the beam.
Calculate the shaft diameter and torsion angle since the maximum torsional moment is 150 Nm for a 1 meter long shaft with a permissible shear stress of 320 MPa G=80 GPa
A flat belt, of density 1000 kg/m3 has a maximum permissible stress of 2·5 MN/m². Thebelt is 200 mm wide and 12 mm thick.(a) Determine the maximum power that can be transmitted if the ratio of tight-side toslack-side tension is 2. The diameter of the driving pulley is 900 mm and the required speed of the output shaft is955 rev/min(b) Taking the belt thickness into account, determine the required diameter of theoutput pulley. (c) What would the required diameter be, assuming a total slip of 4%? (d) If the mass of the belt was neglected, explain the effect (with reasons) this wouldhave on the maximum power calculated in (a)
3) The force, FT = 1 kN, and moment, MT = 0.5 kN-m, at the tip are caused by a wing tip vortexand a winglet, not shown. L = 12 m and the spar has an elastic modulus of E = 70 GPa and aPoisson’s ratio of n = 0.33. The mass of the wing is 4000 kg, and the weight of the engine is 107kN. Use 9.8 m/s 2 for the acceleration due to gravity.Consider the cross-section shown (you can look these up). Pay attention to the coordinate systemgiven in the drawing.d) where is the centroid?e) what is the area?f) Calculate the shear modulus
3) The force, FT = 1 kN, and moment, MT = 0.5 kN-m, at the tip are caused by a wing tip vortexand a winglet, not shown. L = 12 m and the spar has an elastic modulus of E = 70 GPa and aPoisson’s ratio of n = 0.33. The mass of the wing is 4000 kg, and the weight of the engine is 107kN. Use 9.8 m/s 2 for the acceleration due to gravity.Consider the cross-section shown (you can look these up). Pay attention to the coordinate systemgiven in the drawing.g) Compute each of these moments of inertia with the values b = 0.4 m, d =0.5 m , t =0.1 m.
3) The force, FT = 1 kN, and moment, MT = 0.5 kN-m, at the tip are caused by a wing tip vortexand a winglet, not shown. L = 12 m and the spar has an elastic modulus of E = 70 GPa and aPoisson’s ratio of n = 0.33. The mass of the wing is 4000 kg, and the weight of the engine is 107kN. Use 9.8 m/s 2 for the acceleration due to gravity.Consider the cross-section shown (you can look these up). Pay attention to the coordinate systemgiven in the drawing.a) what is the moment of inertia about y-axis in terms of the symbolic dimensions shown?b) what is the moment of inertia about z-axis in terms of the symbolic dimensions shown?c) what is the polar moment of inertia in terms of the symbolic dimensions shown (i.e.about the x-axis)?d) where is the centroid?e) what is the area?f) Calculate the shear modulusg) Compute each of these moments of inertia with the values b = 0.4 m, d =0.5 m , t =0.1 m.