Which of the following statements are true of dislocations? Select one or more: a. Dislocations can be viewed with high powered microscopy and not with the naked eye b. Dislocations can move under stress c. Dislocations can arise due to shear deformation of the lattice □d. Dislocations primarily enable high stiffness in metals

Which of the following statements are true of dislocations? Select one or more: a. Dislocations can be viewed with high powered microscopy and not with the naked eye b. Dislocations can move under stress c. Dislocations can arise due to shear deformation of the lattice □d. Dislocations primarily enable high stiffness in metals

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.6P: An iron specimen is plastically deformed in shear by 1%, and it has u dislocation density of 1 10 14...

See similar textbooks

Similar questions

An iron specimen is plastically deformed in shear by 1%, and it has u dislocation density of 1 10 14 m/ m 3 Assume that the dislocation density did not change in the 1% strain of thisspecimen, the Burger's vector (b) is a 2 [1 1 1] the slip plane is (110). the shear stress isapplied to the (110) plane, and the lattice parameter of the BCC iron is 0.286 nm. Calculate the magnitude of the Burger's vector for these dislocations in iron. Calculate the average distance moved by the mobile dislocations as a result of the 1% shear strain.
Which of the following is false regarding factor of safety in the design of structures? a. It considers uncertainties in the material properties. b. A higher factor of safety is preferable in designing safe structures c. It should not be less than 1 to ensure the structure’s safety. d. It considers changes in the loading pattern on the structure. Which of the following occurs when the value of Poisson’s ratio is doubled and the modulus of elasticity is kept constant? a. The lateral deformations experienced by the material is halved b. The volume of the material will remain constant when subjected to external forces c. The elastic region of the shear stress-strain diagram would be less steep d. The material can withstand higher amounts of stress before permanent deformations occur
Suppose you would like to introduce an interstitial or large substitutional atom into the crystal near a dislocation. Would the atom fit more easily above or below the dislocation line shown in Figure? Explain.
With the help of a diagram, contrast the stress-strain relationship with respect to ceramic and metalsWith the help of a diagram, contrast the stress-strain relationship with respect to ceramic and metals
A bronze rod is rigidly attached between an aluminum rod and a steel rod as shown in the figure below. Axial loads are applied at the positions indicated. a) Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in bronze of 100 MPa, or in aluminum of 90 MPa. b) Determine the deformation of the bronze rod if the value of P is 22.50 KN. The moduli of elasticity are 200 GPa for steel, 80 GPa for bronze and 70 GPa for aluminum.
A Analyse the beam shown by the method of Consistent deformation
8. Elastic deformation, Ductile deformation and Permanent stage are the three stages of deformation True False
The rigid bar is supported by a pin at A and two metal wires,each having a diameter of 4mm.The stress-strain diagram of the steel is given in the Figure below.The lower graph is the zoomed view of the elastic deformation and yielding phases of yielding phases of the stress-strain diagram given by the upper graph.a)Obtain the Young’s modulus of metal.What can you say about the kind of metal considering the Young modulus?If the poınt G is displaced 1.5 mm in vertical direction) b)Determine the forces at wires EB and DC c)the intensity of the distributed load w? d)the final diameters of wires.(Poisson’s ratio is v=0.3)
Materials can have different masses but equal volumes. a. TRUE b. FALSE
A single crystal of BCC iron is subjected to tensile stress of 100 MPa along the [001] direction. Which of the two slip systems ((211) –[ 111 ] or (321)–[ 111 ]) is going to yield first?