Which of the following statements is NOT true?

Q: Which of the following describes something that sugar cube and a leg cube have in common? (a) They…

A: The sugar cube is granulated sugar that has been mixed with a very small quantity of water and then…

Q: Question 25 Which of the following statements about the pressure of a gas is true? None of these are…

A: Write the equation for the absolute pressure. PA=PG+PAtm Here, The absolute pressure is "PA" The…

Q: Which of the following is true? A. csc(-θ)=cscθ B. tan(-θ)=tanθ C. sin(-θ)=sinθ D.cos(-θ)=cosθ

A: Option D is correct Cos (-θ) = Cos θ Where sin (-θ) = - sin θ Tan θ=sinθcosθ Therefore , Tan(- θ)= -…

Q: TRUE OR FALSE

A: This is false. According to Newton's relativity theory, the observer on the spaceship is measured a…

Q: the minimum power required

A: Given; Determine the minimum power required to pump the water across the pipe ?Where,  Pressure drop…

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: The above statement is false.

Q: Answer this correctly  Just answer coorect no needed explanation

A: The correct answer is 4  Doesn't depend on temperature.

Q: Which of the following does not belong to the group? force stress time velocity

A:

Q: Determine the statement is true or false

A: gIVEN; Any thermodynamic cycle operation between two temperature limits is reversible if the product…

Q: product of velocity and mass of fluid particle is known as momentum. Select one: True False

A: Yes, it is true

Q: the difference between two question ?

A: There are no difference between the two two questions

Q: Which of the following is an accurate statement? A The direction of the angular momentum is…

A: option C is the correct answer

Q: Which of the following pressure is the highest? a. 25x10-4 Pascal b. 45 micro Pascal c. 0.03…

A:

Q: Galvanizing is a process of coating the low carbon steel with a layer of zinc. Select one: True…

A: Different types of rust preventive processes used in engineering applications are: Powder Coating…

Q: The possibility to make the required shape from the material is considered during the criteria for…

A: Material to make the desired shape is considered during the criteria of selection. Because during…

Q: This statement is true or false? Process of making raw material to a final desired product is called…

A: Given Data : Raw Material Final desired product

Q: following comparisons is always true?

A: Given: GA=2GB Same poisson's  ratio and yield shear stress for A and B

Q: Which of the following statements are TRUE,

A: Given, Choose the correct parameter for the given statements,where, Cavitation parameter σ=0.

Q: The students are required to explain the following terms using the figures along with the…

A: Linear motion is the motion of the particle moving in the straight line. It is a one dimensional…

Q: True or False: To produce the minimum pressure on a given channel, all other properties be constant,…

A:

Q: A free body diagram is one that shows the complete pictorial representation of the situation Select…

A:

Q: answer question 4)b

A:

Q: What is the temperature of low

A: Given; A carnot cycle is having an efficiency of;  ηcarnot=0.75  High temperature reservior;…

Q: Drilling fluid (drilling mud) is it Newtonian or non-Newtonian?

A: Drilling Fluid: These are also called drilling mud is used to help in drilling of boreholes into the…

Q: Which of the following can be the vacuum pressure?

A: In the above question, it is asked about vaccum pressure. All the options needed to be defined…

Q: The Fusible plug in a boiler is used to prevent damage to the boiler: OPTIONS: 1.May be 2.False…

A: Given Statement:- The Fusible plug in a boiler is used to prevent damage to the boiler.  Options…

Q: Describe any three uses of the following gauge.

A:

Q: specific weight is also known as weight. select one: True False

A: Answer: False

Q: Which of the following statement is NOT correct? Fluid Mechanics is the study of the behaviour of…

A: Mechanics is a branch of science which deals with the forces and its effects like deformation,…

Q: The critical point of a substance is th Select one: O True O False

A: False.

Q: criterion, which one of the following statements is true?

A: Given data; as given in fig,   two states of stress is shown in configuration we have to find with…

Q: a steel wall a temperati

A:

Q: Which one(s) of the following statements is true for limiting positions? Select all that apply.

A: In the four-bar mechanisms, the limiting positions cannot always be avoided. Hence statement (a) is…

Q: Heat output to the system is positive a. False O b. True

A: Answer -false Difference between work and heat is Work Input - the input is considered as negative…

Q: what will be the pressure of the air in

A: P1 = 1 atm = 14.7 psi T1 = 0 oF = 255.37 Kelvin V1 = 100 ft3 T2 = 200 oF = 366.5 Kelvin V2 = 1 ft3…

Q: Which of the followings is true?

A:

Q: one of the following statements is FALSE?

A: Given data: Two dimensional incompressible flow  field given as,               ⇒u=A(XI-YI→)    where…

Q: answer questions d e and f only

A:

Q: Fighter planes fly at 35,000 ft elevation. What must be the muzzle

A: Given data: The elevation of planes, h=35000 ft. The final velocity of the muzzle is, v=0. Write…

Q: of the following causes increase in the diameter of a steam

A: Given Data : Increase in diameter of stem

Q: The A 8000 lb TIT 6000 lb -4 ft. 10.000 lb 4 ft-> 4 4 ft → 4 fi B

A:

Q: force in member [ED] : F(ED) force in member [DC] : F(DC) force in member [BC] : F(BC) Which…

A:

Q: Which side will go down? A! 5m 5m 10KG 5KG B

A:

Q: One of the following is not high alloy steel . O Stainless steel nickal steel tool steel nickel…

A:

Q: Mercury does not wet the wall of the tube of thermometer. Select one: True False

A: As the intermolecular forces between the liquid mercury molecule (Cohesive forces) are stronger in…

Q: Which of the following has multiple degrees of freedom? Option 3 O Option 1

A: Multi-degree-of-freedom (multi-DOF) systems are those in which the motion is described by two or…