Which of the following techniques would NOT result in a titration error? a. Adding 100mL of distilled water instead of 50mL to the vinegar sample. O b. Rinsing the burette with distilled water prior to filling it up with the titrant. O c. Reusing an uncleaned Erlenmeyer flask for the second trial of titration. O d. Titrating duplicate trials of soda samples within a 30-minute interval.

Which of the following techniques would NOT result in a titration error? a. Adding 100mL of distilled water instead of 50mL to the vinegar sample. O b. Rinsing the burette with distilled water prior to filling it up with the titrant. O c. Reusing an uncleaned Erlenmeyer flask for the second trial of titration. O d. Titrating duplicate trials of soda samples within a 30-minute interval.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter17: Complexation And Precipitation Reactions And Titrations

Section: Chapter Questions

Problem 17.7QAP

See similar textbooks

Similar questions

A suitable target for the titration is 30.0 cm3 of 0.025 moldm-3 Br2(aq) Justify why a much smaller target titre would not be appropriate Calculate the amount in moles of bromine in the target titer Justification? calculate a suitable massof alive oil to transfer to the volumetric flask using your answer to of above question and the structure of Y Assume that the olive oil contains 85/- of Y by mass (If you were unable to calculate the amount of bromine in the target titer,you should assume it is 6.25×10^-8 mol .this in not the correct amount)
For titration, what is the purpose of a dropwise rate?
What happens when a non-standard titrant is used in the titration of an unknown sample?a - The volume of the acid used will not be accurate.b - The normality of the acid used will not be accurate.c - The weight of the analyte will not be accurate.d - It will not matter.
Why you can't always use M1V1 = M2V2 in all titration problems?
In a Li2CO3 solution, if it is not adequately filtered before titrations and solid remains, what type of error is created?
Aside from repeating the experiment, what can be done to remedy a sample that is ‘over-titrated’.
Which is the correct order of steps in the preparation of a hydrochoric acid standard solution with sodium bicarbonate standard solution. I. Dissolved sodium carbonate (13.25 g) in about 150 mL of distilled water in a beaker II. Solution of sodium carbonate was transferred into a volumetric flask and diluted to mark before mixing. III. Weigh the appropriate amount of the primary standard. IV. Titrate with enough volume of the acid to completely neutralize the base. V. Transfer 10.00 ml primary standard into an erlenmeyer flask and add indicator III, I, II, V, IV III, II, I, V, IV V, III, I, II, IV V, IV, III, I, II
How would the results of an experiment change if a basic buffer was utilized instead of an acidic one? in this experiment a strong base and strong acid are titrated agaisnt water and an acidic buffer. however, how were the reuslts differ with a basic buffer? please explain
im writing a. lab report with the tittle THE DETERMINATION OF HYDROGEN PEROXIDE BY IODOMETRIC TITRATION I dont know what exactly to introduce in the introduction
How do I determine the concentration of hydrochloric acid through acid-base titration? I mean what experiment could be done to do it. Like what materials or methods to use
Benzoic acid extracted from 123.16 g of sample required a 27.13 mL titration with 0.0792 M barium hydroxide. What is the percent benzoic acid in the sample?
A sample is known to contain about 20% soda ash. What sample size should be taken for analysis, if it is to be dissolved into a 50 mL volumetric flask, with 10 mL aliquots analyzed, if it is desired that the analysis consume a total of 40 mL 0.10 M HCl with 10 mL of 0.10 M NaOH used in the back-titration, after boiling.