Which one of the following statements about DRAM and SRAM is false? Group of answer choices SRAM is usually faster to read from than DRAM DRAM is built using a capacitor to hold charge for logic 1 or 0 SRAM is considered to be non-volatile memory while DRAM is considered volatile Per bit stored, DRAM

Which one of the following statements about DRAM and SRAM is false? Group of answer choices SRAM is usually faster to read from than DRAM DRAM is built using a capacitor to hold charge for logic 1 or 0 SRAM is considered to be non-volatile memory while DRAM is considered volatile Per bit stored, DRAM

Comptia A+ Core 1 Exam: Guide To Computing Infrastructure (mindtap Course List)

10th Edition

ISBN:9780357108376

Author:Jean Andrews, Joy Dark, Jill West

Publisher:Jean Andrews, Joy Dark, Jill West

Chapter3: Supporting Processors And Upgrading Memory

Section: Chapter Questions

Problem 10TC: THINKING CRITICALLY If 2 bits of a byte are in error when the byte is read from ECC memory, can ECC...

See similar textbooks

Similar questions

Q: Choose the correct answer: 1. The signal used to insert Tw state: a. RESET b. HLT 2. DRAM access time is: a. (500-700) n sec b. (0.05-0.07) μ sec C. READY d. RD c. (5-7) µ sec d. Neither a, b, nor c 3. If you have a ROM of size 5060 byte, suitable the number of address line to cover it is: a. 11 address lines b. 12 address lines c. 13 address lines d. 14 address lines 4. In isolated input/output port, port 27 (16-bit port) is: a. Port 53 & 54 (8-bit port) b. Port 54 & 55 (8-bit port) 5. The ROM type that can erase its data is: a. PROM b. EPROM c. Port 26 & 27 (8-bit port) d. Port 27 & 28 (8-bit port) c. EEPROM d. b & c
choose the correct answer :- 1- Which of the following statements about asynchronous circuits is false? a) Memory elements are easy to design and analyze because they are updated at the same time. b) Updates are fast as they depend on instantaneous and individual propagation delays. c) Power consumption is low. d) Since those Memory elements are updated at different times, their designs and analyzes are difficult. 2- Which of the following is true about Synchronous Circuits? a) Since memory elements are updated at different times, their design and analysis are difficult. b) Updates are common and should take longer than the slowest propagation delay in the circuit. This is why they are slow. c) Power consumption is low. d) Updates are fast as they depend on instantaneous and individual propagation delays. 3- Which option has been given the correct naming of asynchronous memory elements? a) O Holder or latch b) O None c) Memory Element d) Flip Flop 4. Using Set-Reset Latch,…
Which of the following is true? 1) the 80/20 rule states that 80% of the instructions is excutede and 20% of the instruction is generated. 2) in von Neumann architecture, external bus is for data memory only
What is the minimum size of a register named 'counter' if you need to set it to 50,000,000 count? Number declaration in Verilog can be in any of the four number systems, namely, decimal, octal, binary, and hexadecimal. True False Assuming that your FPGA is connected to a 10MHz clock, what should be the maximum counter to set if you need a blinking interval of half second?
When the ROM sends data to the microprocessor, which of these conditions are true? a. Both (RD)' and M/(IO)' signals should be low b. (WR)' signal should be low c. (RD)' signal should be low d. M/(IO)' signal should be high e. Both (WR)' and M/(IO)' signals should be low f. (RD)' signal should be active and M/(IO)' signal should be high
Which of the following general statments about computer hardware is/are true? Check all that applya) SRAM usually uses more power than DRAMb) Both multiplexors and busses can be imlemented using tri-state drivers c) In general, inputs are latched at the start of a clock cycle and outputs are enabled at the end. d) It is easy to support multiple simultaneous writers on a bus. e) According to the following diagram: If A=0, B=0, C=1, and D=1, the output is driven to E=0.
Choose an answer and write the procedureIn a microcontroller, the interior of the memory that goes from 0x200 to 0x21FF has been reserved for the program code.What is the maximum size that a program code can have?A) 256B) 512C) 1024D)128
Suppose that four different four-bit numbers are to be taken from memory and added by the circuit discussed in class. How many CLEAR pulses will be needed? How many TRANSFER pulses? How many LOAD pulses?
The byte addresses assigned to the internal SRAM are _______ to _______ in ATmega328. (Hint: To calculate the address of the last location, add the size of SRAM in ATmega328 to the address of the first location of SRAM and decrease the result by one.)
Imagine I had a memory with 256 memory cells arranged in a grid 8 columns wide and 32 rows tall. Further, imagine that I want to fetch the value at memory address 7, so I send the bits 00000111 to the MAR and a "fetch" signal to the Fetch/Store controller via the system bus. Explain the rest of this fetch process. Be specific in terms of what bits will be sent to the decoders and what they will do with those inputs. Typed answer only
Computer Science Please answer this question in assembly language with .asm extension. The code given in 99Heater.asm file is: ; ===== Heater and Thermostst on Port 03 ==========================; ===== 99Heater.asm ==============================================; ===== Heater and Thermostst on Port 03 ========================== MOV AL,0 ; Code to turn the heater off OUT 03 ; Send code to the heater IN 03 ; Input from Port 03 AND AL,1 ; Mask off left seven bits JZ Cold ; If the result is zero, turn the heater on HALT ; Quit Cold: MOV AL,80 ; Code to turn the heater on OUT 03 ; Send code to the heater END; ================================================================= Fix the program 99Heater.asm so that the temperature will stay at 21 ºC. Please solve the question in assembly language. I will definitely give you THUMBS UP.
1. What is the optimum size of the memory?2. What is the size of the state decoder? 2 x 4 3 x 8 4 x 16 5 x 32 6 x 64 3. Which of the following is the correct input to the state counter? "0, IR[2:0]" "1, IR[2:0]" "IR[2:0], 0" "IR[2], 0, IR[1:0]" 4. What state/s should activate the CLR control line of the state counter?